Graco Inc.

Dispensit-Ventile 1052 und 1053  Präzises Dispensierventil

Stangenventile zur Messung der positiven Verdrängung für hochviskose Materialien

HändlersucheInformationen anfordern

Die Stangenventile mit positiver Verdrängung der Modelle 1052 und 1053 wurden für das Dispensieren von volumetrischen Einzelschüssen (1052) oder Perlen (1053) einer Vielzahl von Materialien entwickelt.

  • Für niedrig- bis hochviskose Materialien mit verschiedenen benetzten Komponentenkonfigurationen
    für abrasive gefüllte oder korrosive Materialien
  • 1052 ist ein pneumatisch gesteuertes Ventil mit einem im Mikrometerbereich einstellbaren Dispensiervolumen
    für das genaue, wiederholbare Dispensieren von Schüssen
  • 1053 ist ein servogesteuertes Ventil für das programmierbare, präzise Dispensieren von Schüssen oder Perlen
  • Pneumatische und elektronische Steuerungen können für automatisierte Anwendungen integriert werden
  • Messung der positiven Verdrängung
  • Breite Palette an benetzten Komponenten

Dispensit 1053-10C
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
300°F
149°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
2 in.: 17.85 x 6.23 x 2.91 in
453 x 158 x 74 mm
453 x 158 x 74 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel

Dispensit 1052
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
150°F
65°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.600 cc
0.002 cc to 3.600 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 60 cycles per minute
Up to 60 cycles per minute
Dimensions (H x L x W), height to end of material inlet
16.13 x 5.52 x 2.75 in.
410 x 140 x 70 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 4 - 5 lb
1.81 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel

Dispensit 1053-10B
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
150°F
65°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
2 in.: 17.85 x 6.23 x 2.91 in
453 x 158 x 74 mm
453 x 158 x 74 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel