Graco Inc.

ToughTek P30 and P30ht Mortar Pump  Portable rotor stator pump for mortar and cementitious materials

Built for mid-range applications

مكان الشراء
مشاركة |
M680_Mortar_IMG_1317.tif

Small and compact, yet large enough to get the job done

No matter what type of mortar you’re pumping, the ToughTek P30 Mortar Pump provides long-lasting durability and rugged performance – and handles a wide range of mortar materials. Its compact design and light weight make it easy to transport and use on the jobsite. Reduce manual labor and start pumping with the P30 Mortar Pump instead. Two models: P30 and P30ht High Torque (for epoxy applications). Formerly named Machine Technologies P25.

Materials and applications:

  • Fireproofing materials including:
    • Gypsum-based sprayed fire resistive materials (SFRMs)
    • Cementitious SFRMs
  • Self-leveling underlayment
  • Mortars
  • Epoxy-based mortars
  • Waterproofing
  • Epoxy cladding
  • Non-slip coatings
  • Concrete repair mortars

*Some materials require special handling and testing; contact Graco or your distributor for assistance.

ToughTek P30 Mortar Pump

Say goodbye to buckets. Let the P30 do the work!

  • Easy to use, easy to move
  • Variable pump output lets you adjust material flow
  • Optimal remote control operation
  • Flow rate: 10 gpm (38 lpm)
  • Output (underlayment): 200 bags per hour (based on 50-lb/22.6 kg bags) 
  • Pumping distance: 100 feet + (30 m)
  • Pumping height: 60 feet (18 m)
  • Reversible pump direction
  • Hopper capacity: 16 gal / 2.2 cubic ft
  • Power requirements: 230V, 30A, 1-ph
  • Easy to take apart for quick clean-up and transport
  • Easy to maintain with long-wearing parts and components

أدلة المستخدم

الأدب

عرض القيم بالقيم المترية. عرض القيم بوحدات الولايات المتحدة.
M680 Mortar Sprayer Package
Maximum Working Pressure
1000 psi
7 MPa, 70 bar
Maximum Air Inlet Pressure
100 psi
0.7 MPa, 7 bar
Minimum Inlet Air Flow (Typical)
30 standard cubic feet per minute
0.85 cubic meters per minute
Minimum Inlet Air Flow (Pump Only)
8 scfm per gallon at 100 psi
0.06 cubic meters per minute per liter at 7 bar
Pressure Ratio (Fluid to Air)
10:1
10:1
Air Motor Piston Diameter
7.5 in.
191 mm
Stroke Length
4.75 in.
120 mm
Lower Output
41.9 cu. in. per cycle
686 cc per cycle
Flow Rate at 30 cycles per minute
5.44 gpm
20.6 lpm
Flow Rate at 60 cycles per minute
10.88 gpm
41.2 lpm
Air Inlet Size
3/4 npt(f) (Chicago Fitting)
3/4 npt(f) (Chicago Fitting)
Fluid Inlet Size
2 in. Cam Groove (Male)
2 in. Cam Groove (Male)
Fluid Outlet Size
1 npt(f) with a 1 in. Cam and Groove Fitting
1 npt(f) with a 1 in. Cam and Groove Fitting
Weight (without fluid)
250 lb, (with 25 ft of 1 in. hose and 10 ft of 3/4 in. hose)
113 kg, (with 7.6 m of 25 mm hose and 3.0 m of 19 mm hose)
Sound Pressure
118 dB(A)*
118 dB(A)*
Sound Power
118 dB(A)*
118 dB(A)*
Dimensions
Height
44.5 in.
113 cm
Width
27.5 in.
70 cm
Depth (pump on cart only)
32 in.
81 cm
Deep (pump on cart with hopper)
37 in.
94 cm
Maximum Pump Speed, Do not exceed maximum recommended pump speed of fluid pump to prevent premature pump wear)
Spraying
40 cycles per minute (typically less than 10 cycles per minute)
40 cycles per minute (typically less than 10 cycles per minute)
Flushing
60–90 cycles per minute (only when pumping flushing fluid)
60–90 cycles per minute (only when pumping flushing fluid)
Wetted Parts
Entire System
Stainless steel, UHMWPE, nylon, plated steel, anodized aluminum, FX-75
Stainless steel, UHMWPE, nylon, plated steel, anodized aluminum, FX-75
Pump
Stainless steel, carbide, PTFE, UHMWPE, solvent-resistant o-rings
Stainless steel, carbide, PTFE, UHMWPE, solvent-resistant o-rings
Hose Kits
Nylon core, plated carbon steel fittings, anodized aluminum, nitrile gaskets
Nylon core, plated carbon steel fittings, anodized aluminum, nitrile gaskets
Notes
* Spraying simulated acoustical texture under typical conditions as specified by the material manufacturer.