Graco Inc.

Viscon Fluid Heaters  High performance fluid heaters

Provides excellent temperature conditioning for high solids coatings and high viscosity materials

Kust ostaTeabepäring

Graco's Viscon heaters maintain optimal temperatures to provide consistent control of fluid viscosity. With a wide temperature operating range, Viscon heaters are excellent for any coating, sealant, adhesive or lubricant you need to pump.

Viscon HF High Flow Fluid Heaters
- Designed for high flow rates, with more power for faster material heating

Viscon HF Fluid Heaters for Explosive Atmospheres
- Developed to handle the highest viscosity coatings such as 100% solids epoxies coatings and epoxy fireproofing materials

Viscon HP High Output Fluid Heaters
- Offers high pressure (7250 psi/500 bar) for use with most pumps


Viscon HF Heater with Manual Thermostat Control


Viscon HF High Flow Fluid Heater

  • Spiral passages provide three times the flow rate of standard Viscon heaters
  • Efficient and powerful for faster material heating - gets the job done faster
  • Available in manual thermostat or externally controlled versions
  • Excellent for high solids coatings and protective coatings materials
  • Easy to clean and maintain
  • 7250 psi (500 bar, 50 MPA)
  • Temperature operating range: 84 to 219°F (29 to 104°C)
Viscon_HF_Ex


Viscon HF Fluid Heaters for Explosive Atmospheres

  • The patent-pending design has a triple-path spiral core that can be easily disassembled for cleaning.
  • Increased flow capacity: The Viscon HF has over three (3) times more flow capacity compared to the standard Viscon HP heaters.  
  • Increased heat capacity: The Viscon HF heaters have 35% more wattage; 5400 watts compared to 4000W for the standard Viscon HP heaters.
  • Available in manual thermostat or externally controlled versions.
  • Cleanable and replaceable fluid core – repair instead of replace.
  • 7250 psi (500 bar, 50 MPA) pressure rating – handles the highest pressure rating of Graco protective coating sprayers.
  • Temperature operating range: 84 to 219°F (29 to 104°C)
  • Same mounting configuration as standard Viscon HP heaters – Easy to retrofit onto existing equipment.

Viscon Std Heater



Viscon HP High Output Fluid Heater

  • Higher pressure for use with most pumps
  • Excellent for high solids coatings, adhesives or resins
  • 7/16 in (11 mm) diameter fluid passages
  • Stainless steel design
  • Available in standard or explosive atmosphere versions
  • 7250 psi (500 bar, 50 MPa)
  • Temperature operating range: 84 to 219°F (29 to 104°C)

Viscon HF
U.S.
Metric
Metric
The heater can be used in the following environmental conditions: indoor use, 99% maximum relative humidity, pollution degree 2, installation category II, maximum ambient temperature 135° F (57° C).
Maximum Working Pressure
7250 psi (50 MPa, 500 bar)
7250 psi (50 MPa, 500 bar)
Voltage / Wattage / Current*
See Models on page 2.
See Models on page 2.
Fluid Passage Heat Transfer Area
210 in.² (1355 cm²)
210 in.² (1355 cm²)
Fluid Passage Dimensions (3 parallel paths)
Height: 0.41 in.
Height: 0.41 in.
Width: 0.32 in.
Length: 3 x 48 in.
Fluid Passage Equivalent Diameter
0.72 in. (18.3 mm)
0.72 in. (18.3 mm)
Thermometer Range
64 - 250°F (18 - 121°C)
64 - 250°F (18 - 121°C)
Wetted Parts
Stainless Steel, Anodized Aluminum, Electroless Nickel-Plated Steel, PTFE
Stainless Steel, Anodized Aluminum, Electroless Nickel-Plated Steel, PTFE
Temperature Operating Range
84 - 219°F (29 - 104°C)
84 - 219°F (29 - 104°C)
Weight
51 lb (23.2 kg)
51 lb (23.2 kg)
RTD (Model 262853 only)
1000 ohm, class B, 3-wire Connector: M8, 4-pin male
1000 ohm, class B, 3-wire Connector: M8, 4-pin male
Main supply fluctuation not to exceed 10%.