Graco Inc.

XM70 이액형 도장기  간편하고 저렴한 이액형 도장

이액형 고고형분 코팅을 위한 고압 성능

정보 요청

수동 혼합에 대한 스마트한 대안

Graco XP70 이액형 도장기는 탁월한 결과와 함께 고점도 고고형분 코팅을 주입, 혼합, 분무하도록 설계되었습니다. 또한 XP70은 사용자가 중력식 공급을 통해 공급 펌프의 필요성을 제거함으로써 비용을 절감할 수 있도록 설계되었습니다. 수동 혼합으로부터 업그레이드를 하면 XP70이 도료 낭비 및 세정용 용제 사용 감소를 통해 탁월한 투자 수익을 제공한다는 사실을 알게 됩니다.


Resources(자원) 탭의 ROI 계산기를 사용하여 비용 절감액을 확인하실 수 있습니다.

수동 혼합으로부터의 전환을 통해 많은 혜택을 얻을 수 있음

Graco XP50 protective coatings application
  • 도료 낭비 감소 
  • 작업 완료 후 더 이상 사용하지 않은 도료를 버릴 필요가 없음
  • 세정용 용제 사용 감소로 비용 절감
  • 일정한 도료 품질 - 도료 측정에서 추측의 필요성이나 인간의 실수가 사라짐
  • 손쉬운 작동 - 최소 훈련만 필요
  • 유지보수 비용 절감
  • 고점도 도료와 긴 호스 길이를 위한 7250 psi (500 bar, 50 MPa)의 정격

매뉴얼



XP and XP-h Proportioners
Maximum Fluid Working Pressure
See Models section in instruction manual.
See Models section in instruction manual.
Maximum Air/Hydraulic Oil Working Pressure
See Models section in instruction manual.
See Models section in instruction manual.
Combined Fluid Output (cc/cycle)
See Models section in instruction manual.
See Models section in instruction manual.
Pressure Ratio
See Models section in instruction manual.
See Models section in instruction manual.
Fluid Flow at 40 cpm
See Models section in instruction manual.
See Models section in instruction manual.
Hydraulic Fluid Consumption (XP-h models only)
0.2 gallons per cycle
0.76 liters per cycle
Air inlet size
3/4 npsm(f)
3/4 npsm(f)
Maximum air pressure supply to the system
175 psi
12 bar, 1 MPa
Fluid pump inlets without hoppers
1-1/4 in. npsm(m)
1-1/4 in. npsm(m)
Fluid gauge manifold outlets
1/2 in. npt(f)
1/2 in. npt(f)
Fluid mix manifold inlets
1/2 in. npt(f) ball valves
1/2 in. npt(f) ball valves
Mix manifold material outlet
1/2 in. npt(f)
1/2 in. npt(f)
Maximum feed pressure from remote source
250 psi
17 bar, 1.7 MPa
Sound pressure
86 dBA at 100 psi
7 bar, 0.7 MPa
Sound power
98 dBA at 100 psi
7 bar, 0.7 MPa
Maximum Storage Time
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
Maximum Lifetime
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
Power Efficiency Factor (XP70)
75 cu. ft compressed air/1 gallon sprayed material at 100 psi
2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa)
Air consumption per 1 gallon (3.78 l) of flow
XP70
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
XP50
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
XP35
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
Filtration
Air inlet filtration
40-micron filter/separator included
40-micron filter/separator included
XP pump outlets
30 mesh
30 mesh
XTR Spray Gun
60 mesh
60 mesh
Fluid Viscosity Range
Gravity feed with 7 gallon (26 liter) hoppers
200 to 20,000 cps (pourable)
200 to 20,000 cps (pourable)
Pressure feed
Any viscosity that will not require feed pressure more than 15% of outlet pressure
Any viscosity that will not require feed pressure more than 15% of outlet pressure
Environmental Rating (Indoor/outdoor)
Hazardous Areas
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
Ambient Temperature Range
Operating
40-130°F
4-54°C
Storage
30-160°F
-1-71°C
Maximum Fluid Temperature
160°F
71°C
Wetted materials
Housings and manifolds
Carbon steel with electroless nickel plating
Carbon steel with electroless nickel plating
Miscellaneous parts
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
Pump packings
Carbon filled PTFE, proprietary UHMWPE
Carbon filled PTFE, proprietary UHMWPE
Flush pump suction tube
Aluminum
Aluminum
Hoses
Nylon core
Nylon core
Weight
Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers
575 lb
261 kg
Full XP-h System with heaters, solvent flush pump, and hoppers
600 lb
273 kg
Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers
425 lb
193 kg
Bare XP-h System with no heaters, solvent flush pump, or hoppers
450 lb
204 kg
XP35, XP50, or XP70 Pump only
286 lb
130 kg
XP-h Pump only
290 lb
132 kg