Graco Inc.

Vannes 1052 et 1053 Dispensit  Vanne de distribution de précision

Vannes de tige de dosage à déplacement positif pour des produits à faible ou importante viscosité

Où acheterDemander des informations

Les vannes modèle 1052 et 1053 à déplacement positif sur tige sont conçues pour la distribution par décharges volumétriques (1052) ou cordons (1053) d'une large variété de produits.

  • Pour des produits à faible ou importante viscosité avec différentes configurations de composants en contact avec le produit
    pour les produits abrasifs ou corrosifs garnis
  • Le modèle 1052 est une vanne commandée pneumatiquement avec des volumes de distribution réglables par micromètre
    pour une distribution par décharges précises et répétées
  • Le modèle 1053 est une vanne commandée par servomoteur pour une distribution par décharges précises et programmables ou par cordon
  • Les commandes pneumatiques et électroniques peuvent être intégrées pour les applications automatisées
  • Dosage par déplacement positif
  • Large gamme de composants en contact avec le produit

Dispensit 1053-10C
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
300°F
149°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
2 in.: 17.85 x 6.23 x 2.91 in
453 x 158 x 74 mm
453 x 158 x 74 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel

Dispensit 1052
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
150°F
65°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.600 cc
0.002 cc to 3.600 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 60 cycles per minute
Up to 60 cycles per minute
Dimensions (H x L x W), height to end of material inlet
16.13 x 5.52 x 2.75 in.
410 x 140 x 70 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 4 - 5 lb
1.81 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel

Dispensit 1053-10B
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
150°F
65°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
2 in.: 17.85 x 6.23 x 2.91 in
453 x 158 x 74 mm
453 x 158 x 74 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel