Graco Inc.

FRP Elyaf Kırpma Sistemi 

Kompozit üretimi için elyaf kırpma/ıslatma sistemi

Satış NoktalarıBilgi İste

Tutarlı bir çözüm için tutarlı oran

Sektörde başarısı kanıtlanmış Graco bileşenleriyle üretilen Graco FRP Sistemleri size teknolojik olarak gelişmiş, sağlam ve dayanıklı bir çözüm sağlar. Graco'nun üstün oran kontrolü, tesisinizde daha kaliteli parçalar ve son ürünler olmasını sağlayan tutarlı bir çözüm sunar.

Graco RS Chop Gun

Consistent ratio for a consistent cure

Engineered with industry-proven Graco components, Graco FRP Systems provide you with a solution that is technologically advanced, durable and long-lasting. Graco's superior ratio control results in a consistent cure, which translates into higher quality parts and end products in your plant.

FRP GEL COAT GUN right

 

Learn about the exclusive technologies that keep Graco's FRP Systems and RS Guns at the industry forefront.

Learn about the exclusive technologies that keep Graco FRP systems and resin guns at the industry forefront.

Graco RS Chop Gun

Consistent ratio for a consistent cure

Engineered with industry-proven Graco components, Graco FRP Systems provide you with a solution that is technologically advanced, durable and long-lasting. Graco's superior ratio control results in a consistent cure, which translates into higher quality parts and end products in your plant.

Graco FRP Chop
  • Sistem, oran kararlılığı için optimize edilmiştir
  • Başarısı kanıtlanmış Graco pompalar ve bileşenlerle üretim çalışma zamanını artırır
  • Ayarlanabilir oranlı katalizör pompa - hızlı, kolay oran değişikliği için hiçbir araca gerek yoktur
  • Üstün oran kontrolü için uzmanca geliştirilmiş bağlantı
  • 13:1 pompa oranında sunulur

FRP Proportioner
Maximum air inlet pressure
100 psi
7 bar, 0.7 MPa
Maximum air inlet pressure to ASME solvent pressure pots
100 psi
7 bar, 0.7 MPa
Typical flow rate of pattern guns
Refer to RS Gun manual.
Refer to RS Gun manual.
A component (catalyst) inlet size
3/8 in tube
3/8 in tube
B component (resin) inlet size
1 5/16-12 UN-2A male
1 5/16-12 UN-2A male
Wetted parts
Stainless steel, carbide, UHMWPE, PTFE, and acetal
Stainless steel, carbide, UHMWPE, PTFE, and acetal
Resin Wetted Parts
Stainless steel, tungsten carbide with 6% nickel, UHMWPE, PTFE, (LW100C displacement pump only: Also includes carbon steel)
Stainless steel, tungsten carbide with 6% nickel, UHMWPE, PTFE, (LW100C displacement pump only: Also includes carbon steel)
Catalyst Wetted Parts (Series A and B systems, built prior to April 2013, have non-metallic nylon catalyst tube fittings. To convert your system to stainless steel fittings, see the FRP Proportioner manual)
301, 303, 304, 316, and 17-4 PH grades of stainless steel, silicon nitride, acetal, perfluoroelastomer, PE, PTFE, UHWMPE, polypropylene
301, 303, 304, 316, and 17-4 PH grades of stainless steel, silicon nitride, acetal, perfluoroelastomer, PE, PTFE, UHWMPE, polypropylene
Maximum fluid working pressure
13:1 Systems:
1300 psi
9 MPa, 90 bar
17:1 Systems:
1700 psi
11.9 MPa, 119 bar
Maximum fluid temperature (Maximum fluid temperature rating determined by lowest rated component in system)
Models with RS Gun
100°F
38°C
Models without RS Gun
160°F
71°C