XP-h Hydraulic Sprayer
Built with patented XP ratio technology, the Graco XP-h Hydraulic Plural-Component Sprayer is ideal for truck, palletized, trailer or flatbed systems that have on-board hydraulic power*. It is well-suited for OEM traffic marking applications. The system’s hydraulic motor has been optimized and rated to match the pressure capabilities of the NXT 6500 air motor used on Graco XP50 and XP70 sprayers.
GH™ Power Pack Accessory
The XP is now more versatile than ever for contractors wishing to take advantage of the convenience and efficiency of a gas-powered hydraulic system. Hydraulic systems are energy efficient and provide very smooth changeovers on the XP resulting in well balanced pressures and the smoothest possible spray pattern.
Target applications include:
Ordering information
| XP and XP-h Proportioners | |
| Maximum Fluid Working Pressure | See Models section in instruction manual. See Models section in instruction manual. |
| Maximum Air/Hydraulic Oil Working Pressure | See Models section in instruction manual. See Models section in instruction manual. |
| Combined Fluid Output (cc/cycle) | See Models section in instruction manual. See Models section in instruction manual. |
| Pressure Ratio | See Models section in instruction manual. See Models section in instruction manual. |
| Fluid Flow at 40 cpm | See Models section in instruction manual. See Models section in instruction manual. |
| Hydraulic Fluid Consumption (XP-h models only) | 0.2 gallons per cycle 0.76 liters per cycle |
| Air inlet size | 3/4 npsm(f) 3/4 npsm(f) |
| Maximum air pressure supply to the system | 175 psi 12 bar, 1 MPa |
| Fluid pump inlets without hoppers | 1-1/4 in. npsm(m) 1-1/4 in. npsm(m) |
| Fluid gauge manifold outlets | 1/2 in. npt(f) 1/2 in. npt(f) |
| Fluid mix manifold inlets | 1/2 in. npt(f) ball valves 1/2 in. npt(f) ball valves |
| Mix manifold material outlet | 1/2 in. npt(f) 1/2 in. npt(f) |
| Maximum feed pressure from remote source | 250 psi 17 bar, 1.7 MPa |
| Sound pressure | 86 dBA at 100 psi 7 bar, 0.7 MPa |
| Sound power | 98 dBA at 100 psi 7 bar, 0.7 MPa |
| Maximum Storage Time | 5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) 5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) |
| Maximum Lifetime | Indefinite with recommended maintenance and periodic rebuilds for critical parts. Indefinite with recommended maintenance and periodic rebuilds for critical parts. |
| Power Efficiency Factor (XP70) | 75 cu. ft compressed air/1 gallon sprayed material at 100 psi 2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa) |
| Air consumption per 1 gallon (3.78 l) of flow | |
| XP70 | 75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) 75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) |
| XP50 | 60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) 60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) |
| XP35 | 50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) 50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) |
| Filtration | |
| Air inlet filtration | 40-micron filter/separator included 40-micron filter/separator included |
| XP pump outlets | 30 mesh 30 mesh |
| XTR Spray Gun | 60 mesh 60 mesh |
| Fluid Viscosity Range | |
| Gravity feed with 7 gallon (26 liter) hoppers | 200 to 20,000 cps (pourable) 200 to 20,000 cps (pourable) |
| Pressure feed | Any viscosity that will not require feed pressure more than 15% of outlet pressure Any viscosity that will not require feed pressure more than 15% of outlet pressure |
| Environmental Rating (Indoor/outdoor) | |
| Hazardous Areas | EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. |
| Ambient Temperature Range | |
| Operating | 40-130°F 4-54°C |
| Storage | 30-160°F -1-71°C |
| Maximum Fluid Temperature | 160°F 71°C |
| Wetted materials | |
| Housings and manifolds | Carbon steel with electroless nickel plating Carbon steel with electroless nickel plating |
| Miscellaneous parts | Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics |
| Pump packings | Carbon filled PTFE, proprietary UHMWPE Carbon filled PTFE, proprietary UHMWPE |
| Flush pump suction tube | Aluminum Aluminum |
| Hoses | Nylon core Nylon core |
| Weight | |
| Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers | 575 lb 261 kg |
| Full XP-h System with heaters, solvent flush pump, and hoppers | 600 lb 273 kg |
| Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers | 425 lb 193 kg |
| Bare XP-h System with no heaters, solvent flush pump, or hoppers | 450 lb 204 kg |
| XP35, XP50, or XP70 Pump only | 286 lb 130 kg |
| XP-h Pump only | 290 lb 132 kg |
Roof Coatings
Rust Proofing
Ship Building & Marine
Bridge Protective Coatings
Sprayers for protective coating bridge applications
Railcar Manufacturing and Repair
Towers for Wind Turbines
Pipe and Tank Coating
Structural Steel Coating
Water Tower Protective Coatings
Wastewater Treatment
Manhole and Sewer Reconditioning
Secondary Containment Spill Prevention
Corrosion Control
Offshore Rigs
T1, T2 and T3 Transfer Pumps
Ideal for moving A and B materials to Reactor spray machines
Viscon Fluid Heaters
Provides excellent temperature conditioning for high solids coatings and high viscosity materials
XTR-5 and XTR-7
Airless spray guns for protective coatings
Xtreme-Duty Hose
For high-pressure spraying applications
PressureTrak Ratio Assurance for XP Sprayers
XP35 Plural-Component Sprayer
For low pressure protective coatings applications
XP50 Quick-Set Packages
Optimized for quick-setting coatings
XP50 and XP50-hf Plural-Component Sprayer
For higher-volume protective coatings
XP70 and XP70-hf Plural-Component Sprayers
High-pressure performance for two-part high-solids coatings
