Graco Inc.

Reactor A-XP1  Air-Driven Coatings Proportioner

For polyurea coatings – applies up to 1.5 gal (5.7 L) per minute

Onde comprarSolicitar informações
Share |

The Reactor A-XP1 is a Graco-engineered coatings proportioner that gives you the reliability you expect on the jobsite. It maintains consistent temperature control, even when you're spraying at maximum flow rates – resulting in better quality coating.

  • Maintains temperature setpoints for better yield
  • Maintains consisten output pressure for uniform spray pattern
  • Easy to operate and maintain
  • Best choice for affordability and durability

Ver valores em unidades métricas. Ver valores em unidades dos Estados Unidos.



Reactor A-XP1 Plural Component Proportioner
Maximum Fluid Working Pressure
3500 psi
24 MPa, 241 bar
Maximum Air Supply Pressure
125 psi
0.9 MPa, 9 bar
Maximum Air Working Pressure
100 psi
689 MPa, 6.9 bar
Pressure Ratio
35:1
35:1
Air consumption with 00 tip at 2000 psi stall pressure
32 scfm
0.9m³/min
Machine Maximum Power with hose
13,000 Watts
13,000 Watts
Amperage Requirement (Full Load Peak)*
56 amps @ 230 V, 1 Phase, 45 amps @ 230 V, 3 Phase, 26 amps @ 380 V, 3 Phase
56 amps @ 230 V, 1 Phase, 45 amps @ 230 V, 3 Phase, 26 amps @ 380 V, 3 Phase
Maximum Heater Fluid Temperature
190°F
88°C
Maximum Hose Fluid Temperature
180°F
82°C
Maximum Ambient Temperature
120°F
49°C
Maximum Output
1.5 gal/min at 2000 psi
1.5 gal/min at 2000 psi
Output Per Cycle (A and B)
0.017 gal/cycle
0.094 ltr/cycle
Heater Power
10,200 Watts
10,200 Watts
Hose Power
2790 Watts
2790 Watts
Sound Pressure (see NXT air motor manual)
70.2 dB(A)
70.2 dB(A)
Sound Power (see NXT air motor manual)
80.1 dB(A)
80.1 dB(A)
Viscosity Range
250–1500 centipoise (typical)
250–1500 centipoise (typical)
Maximum Fluid Inlet Pressure
300 psi or 15% of output pressure
2.1 MPa, 21 bar or 15% of output pressure
Fluid Inlet/Strainer Filter
20 mesh standard
20 mesh standard
Air inlet Filter Mesh
40 Micron
40 Micron
Component B (Resin) Inlet
3/4 npt(f) swivel
3/4 npt(f) swivel
Component A (Isocyanate) Inlet
3/4 npt(f) swivel
3/4 npt(f) swivel
Recirculation/Block Hose Connections
Iso (A) side: #5 JIC (m); Resin (B) side: #6 JIC (m)
Iso (A) side: #5 JIC (m); Resin (B) side: #6 JIC (m)
Maximum Heated Hose Length ***
210 ft of 3/8 ID
210 ft of 3/8 ID
Weight
310 lb
140.6 kg
Wetted Parts
Carbon steel, stainless steel, chrome, aluminum, Fluoroelastomer, PTFE, nylon
Carbon steel, stainless steel, chrome, aluminum, Fluoroelastomer, PTFE, nylon
Voltage Tolerance Range (50/60 Hz)
200–240 V ac Nominal, 1 Phase
195–253 V ac
195–253 V ac
200–240 V ac Nominal, 3 Phase Delta
195–253 V ac
195–253 V ac
350–415 V ac Nominal, 3 Phase Wye (200–240 V ac Line-to-Neutral)
338–457 V ac
338–457 V ac
*Full load amps with all devices operating at maximum capabilities with 210 ft (64.1 m) of hose.
***210 ft (64 m) of heated hose will produce the maximum allowable heat capacity. 310 ft (94 m) of heated hose may be used, but will have 25% less heat capacity.