Graco Inc.

Viscon 流体加热器  高性能流体加热器

针对高含固量涂料与高粘度材料进行出色的温度调节

购买地点小帮手咨询信息

固瑞克 Viscon 加热器可维持最佳温度,将对流体粘度的控制保持不变。Viscon 加热器的工作温度为 84-219°F(29-104℃),是泵送涂料、密封胶、粘合剂或润滑剂的极佳选择。

Viscon HF 大流量流体加热器
- 针对高流量设计,功率更高、材料加热更快

Viscon HP 高输出量流体加热器
- 高压可达 7250 psi/500 bar,可配合大多数泵使用

Viscon Fluid Heaters

Viscon HP 高输出量流体加热器

  • 高压可配合大多数泵使用
  • 是泵送涂料、密封胶、树脂的极佳选择
  • 流体通道的直径 7/16 in (11 mm)
  • 不锈钢设计
  • 标准和防爆型号可供选择
  • 压力等级达 7250 psi (500 bar, 50 MPa) 
  • 工作温度:84 到 219°F(29 至 104°C)
Viscon HF Heater with Manual Thermostat Control
Viscon HF Heater with Manual Thermostat Control

Viscon HF 大流量流体加热器

  • 螺旋通道,流量可达标准 Viscon 加热器的3倍
  • 加热功率更高、加热更快——可更快完成作业
  • 手动温控或外部控制供选
  • 高固含量涂料和防腐涂料的绝佳选择
  • 清洁维护简便
  • 压力等级达 7250 psi (500 bar, 50 MPa)  
  • 工作温度:84 到 219°F (29 至 104°C)

Viscon HF
U.S.
Metric
Metric
The heater can be used in the following environmental conditions: indoor use, 99% maximum relative humidity, pollution degree 2, installation category II, maximum ambient temperature 135° F (57° C).
Maximum Working Pressure
7250 psi (50 MPa, 500 bar)
7250 psi (50 MPa, 500 bar)
Voltage / Wattage / Current*
See Models on page 2.
See Models on page 2.
Fluid Passage Heat Transfer Area
210 in.² (1355 cm²)
210 in.² (1355 cm²)
Fluid Passage Dimensions (3 parallel paths)
Height: 0.41 in.
Height: 0.41 in.
Width: 0.32 in.
Length: 3 x 48 in.
Fluid Passage Equivalent Diameter
0.72 in. (18.3 mm)
0.72 in. (18.3 mm)
Thermometer Range
64 - 250°F (18 - 121°C)
64 - 250°F (18 - 121°C)
Wetted Parts
Stainless Steel, Anodized Aluminum, Electroless Nickel-Plated Steel, PTFE
Stainless Steel, Anodized Aluminum, Electroless Nickel-Plated Steel, PTFE
Temperature Operating Range
84 - 219°F (29 - 104°C)
84 - 219°F (29 - 104°C)
Weight
51 lb (23.2 kg)
51 lb (23.2 kg)
RTD (Model 262853 only)
1000 ohm, class B, 3-wire Connector: M8, 4-pin male
1000 ohm, class B, 3-wire Connector: M8, 4-pin male
Main supply fluctuation not to exceed 10%.