Hydra-Cat mit festem Mischverhältnis Mechanischer Dosierer
Die Bauweise mit mehreren Unterpumpen sorgt für eine präzise Dosierung von Zweikomponentenmaterialien
Hydra-Cat Dosierer mit festem Mischverhältnis können Mehrkomponenten-Materialien durch das Einschalten von zwei oder drei Verdrängerpumpen von einem gemeinsamen Luftmotor aus präzise pumpen. Damit wird sichergestellt, dass Hubzahl und Hublänge aller Unterpumpen identisch sind und eine konstante Dosierung bieten.
Modelle mit zwei gleich großen Unterpumpen sorgen für ein Kräftegleichgewicht an den Pumpen, was einen vorzeitigen Verschleiß der Packungen verhindert. Modelle mit drei Unterpumpen und Zylindern unterschiedlicher Größen können für das Bereitstellen einer Vielzahl von Mischverhältnissen gewählt werden.
Soll Ihr Hydra-Cat aktualisiert werden? Siehe Graco-Serie der XP Mehrkomponenten-Spritzgeräte.
- Severe Duty-Unterpumpen für Verschleißfestigkeit und Langlebigkeit
- Konfigurationen aus mehreren Unterpumpen erreichen eine Vielzahl von Mischverhältnissen
- Zwei Unterpumpen bieten ein gleichbleibendes Mischverhältnis von 1:1
- Drei Unterpumpen bieten Mischverhältnisse über 1:1 für ausgeglichenes Pumpen
- PTFE-Packungen sind Standard an den Hydra-Cat-Unterpumpen
Handbücher
- 308225h , Bulldog Hydra-Cat Dosierpumpen mit festem Mischverhältnis [andere sprachen]
- 308224a , President Hydra Cat Dosierpumpen [andere sprachen]
- 192759G, Fixed Ratio Hydra-Cat, Two Lowers, Wall or Stand Mounted, EU-Declaration of Conformity, English (nur in Englisch)
- 192984K, Fixed Ratio Hydra-Cat, Bare Pump Model, EU-Declaration of Conformity, English (nur in Englisch)
- 193731H, Fixed Ratio Hydra-Cat, Wall or Stand Mounted, EU-Declaration of Conformity, English (nur in Englisch)
President Hydra-Cat Fixed Ratio Proportioning Pumps | |
Pumps | |
Air operating range |
40–100 psi
0.3–0.7 MPa, 3–7 bar
|
Air consumption |
See example below
See example below
|
Fluid inlet size |
3/4 npt
3/4 npt
|
Fluid outlet size |
3/8 npt
3/8 npt
|
Air inlet size |
3/4 npt
3/4 npt
|
Maximum fluid outlet pressure |
3000 psi
21 MPa, 210 bar
|
Maximum fluid inlet pressure |
250 psi
1.7 MPa, 17 bar
|
Wetted parts |
Stainless steel, Tungsten Carbide, Chrome plating, Carbon steel, PTFE, Ultra-high molecular weight polyethylene
Stainless steel, Tungsten Carbide, Chrome plating, Carbon steel, PTFE, Ultra-high molecular weight polyethylene
|
Manifold assemblies | |
Manifold outlets |
3/8 npt
3/8 npt
|
Hoses |
3/8 in. ID, PTFE, cpld 3/8 npt(m) 4000 psi maximum working pressure
3/8 in. ID, PTFE, cpld 3/8 npt(m) 28 MPa, 276 bar maximum working pressure
|
Hoses |
3/8 in. ID, nylon, cpld 3/8 npt(m) 3000 psi maximum working pressure
3/8 in. ID, nylon, cpld 3/8 npt(m) 21 MPa, 210 bar maximum working pressure
|
Automatic pressure relief valves wetted parts |
303 stainless steel, Tungsten carbide, fluoroelastomer
303 stainless steel, Tungsten carbide, fluoroelastomer
|
Sound, Tested in accordance with ISO 9614–2. | |
Sound pressure levels (dBa), (Input air pressures at 15 cycles/min.) |
73.6 dB(A) at 40 psi (0.3 MPa, 2.8 bar), 78.3 dB(A) at 70 psi (0.5 MPa, 4.8 bar), 80.9 dB(A) at 100 psi (0.7 MPa, 7 bar)
73.6 dB(A) at 40 psi (0.3 MPa, 2.8 bar), 78.3 dB(A) at 70 psi (0.5 MPa, 4.8 bar), 80.9 dB(A) at 100 psi (0.7 MPa, 7 bar)
|
Sound power levels (dBa), (Input air pressures at 15 cycles/min.) |
87.4 dB(A) at 40 psi (0.3 MPa, 2.8 bar), 92.1 dB(A) at 70 psi (0.5 MPa, 4.8 bar), 94.6 dB(A) at 100 psi (0.7 MPa, 7 bar)
87.4 dB(A) at 40 psi (0.3 MPa, 2.8 bar), 92.1 dB(A) at 70 psi (0.5 MPa, 4.8 bar), 94.6 dB(A) at 100 psi (0.7 MPa, 7 bar)
|
Air consumption example | |
When the air pressure to the pump is 60 psi (410 kPa, 4.1 bar) and you are dispensing 1 gal. (3.8 liter) of mixed fluid per minute, air volume used, in cfm, will be about the same as the larger pressure ratio figure of your pump. See instruction manual for pressure ratios of pumps. Xper minute, air volume used, in cfm, will be about the same as the larger pressure ratio figure of your pump. See instruction manual for pressure ratios of pumps. |
Bulldog Hydra-Cat Fixed Ratio Proportioning Pumps | |
Pumps | |
Air operating range |
40–100 psi
280–700 kPa, 2.8–6.37 bar
|
Air consumption |
See example below
See example below
|
Fluid inlet size |
3/4 npt
3/4 npt
|
Fluid outlet size |
3/8 npt
3/8 npt
|
Air inlet size |
3/4 npt
3/4 npt
|
Maximum fluid outlet pressure |
3000 psi
21 MPa, 207 bar
|
Maximum fluid inlet pressure |
250 psi
1.7 MPa, 17 bar
|
Wetted parts |
Stainless steel, tungsten carbide, chrome plating, carbon steel, PTFE, ultra-high molecular weight polyethylene
Stainless steel, tungsten carbide, chrome plating, carbon steel, PTFE, ultra-high molecular weight polyethylene
|
Manifold assemblies | |
Manifold outlets |
3/8 npt
3/8 npt
|
Hoses |
3/8 in. ID, PTFE, cpld 3/8 npt(m) 4000 psi maximum working pressure
3/8 in. ID, PTFE, cpld 3/8 npt(m) 28 MPa, 276 bar maximum working pressure
|
Hoses |
3/8 in. ID, nylon, cpld 3/8 npt(m) 3000 psi maximum working pressure
3/8 in. ID, nylon, cpld 3/8 npt(m) 21 MPa, 207 bar maximum working pressure
|
Automatic pressure relief valves wetted parts |
303 stainless steel, tungsten carbide, fluoroelastomer
303 stainless steel, tungsten carbide, fluoroelastomer
|
Air consumption example | |
When the air pressure to the pump is 60 psi (410 kPa, 4.1 bar) and you are dispensing 1 gal. (3.8 liter) of mixed fluid per minute, air volume used, in cfm, will be about the same as the larger pressure ratio figure of your pump. See instruction manual for pressure ratios of pumps. |
Verwandte Produkte
-
PressureTrak Ratio Assurance for XP Sprayers
-
XP35 Mehrkomponenten-Spritzgeräte
Für Anwendungen von Schutzanstrichen bei Niederdruck
-
XP50 und XP50-hf Mehrkomponenten-Spritzgeräte
Für höhervolumige Schutzbeschichtungen
-
XP70 und XP70-hf Mehrkomponenten-Spritzgeräte
Hochdruck-Leistung für zweiteilige hochfeste Beschichtungen