The dust free blast solution for on-board surface preparation and spot repair
EcoQuip2 EQp
Whether you plan to remove old coatings on deck or corrosion control on steel structures on-board , it’s time to consider an alternative to your power/pressure washer, chemical cleaners or hand/bristle tools. Graco’s EcoQuip2 EQp is a portable and powerful machine that gets the job done quickly and effectively.
Graco’s Vapour Abrasive blast Equipment (EcoQuip2) reduces dust by up to 92% less than traditional dry blasting. The machine uses very little fresh water compared to power/pressure washers or other wet abrasive blasting technologies and delivers the right surface profile.
Media Funnel and Pop-Up Seal
- Removable for clean-out access
- Built-in strainer
Water/Media Vessel
- 55L capacity
- Blast for up to 90 minutes between refills
- Works with coarse, fine, or non-destructive media
- Universal, Chicago-style claw fitting, common to most 5.2 m³/min (185 cfm) compressors
Enclosure with Controls
- Blast circuit, water pump and air/water controls
Abrasive Supply Line
- Quick-release cam and groove connection
- Easy-access shut-off valve
Portable Cart with Lift Handles
- Weighs only 99.8 kg (220 lbs)
- Easily transports between jobs
- Slide rails for easy loading
Easy-to-use Controls
- Blast air pressure
- Abrasive meter
- Selector valve for washdown or blast
Abrasive Metering Valve
- Precise control of media
- Lockable set-point
Quick-Fill Valve
- Speeds up the fill/flush process with garden hose pressure
- Accepts 1/2" or 1" blast hose
Blast Hose Control Lines
- Pneumatic operation
- Blasts up to 50 meter from machine
Flat-free Wheels
- Rugged and durable to get around your job site smoothly
Please click on the yellow spots
on the unit to read more
Discover the features of Graco’s EQp
1. Small and portable
The dimensions of the Graco EcoQuip2 Eqp make it easy to move the unit on the deck. One person can maneuver the cart and get the unit to the place where the blasting will take place. With the EQp you can blast both horizontal and vertical surfaces. The small size of the blast nozzle allows you to blast in narrow spaces; which is a big advantage when compared with the long – difficult to maneuver - pressure washer guns.
2. ATEX approved
The EcoQuip ATEX equipment has been approved for use in areas with classification Zone 1 and Zone 2. This means the system is approved to operate in an explosive atmosphere consisting of a mixture of flammable substances that can form occasionally in normal operation. The EQp can thus be used on-board all vessel types.
3. Environmental friendly
Testing conducted by a third-party agency shows that vapor abrasive blasting suppresses up to 92% of dust compared to dry blasting. Because dust is minimized, less containment may be required and media clean-up time can be reduced. Since EcoQuip2 uses less water than slurry or other water-based technologies, no pools of water are left behind, and there is less need to worry about toxic runoff. The end result with EcoQuip2 is a cleaner, more effective contained process.
4. Limited Health Risks
Graco’s EQp is the safest solution there is on the market for on-board surface preparation. The blast pressure is maximum 10 Bar (145 PSI) which is very little compared to the dangerous high pressures needed for pressure washing or water jetting. When compared to needle guns and bristle blasters there are little vibrations and thus limited operator fatigue.
5. Proper surface preparation
Blasting with Graco’s EQp ensures you a perfect surface preparation. Which ultimately results in a better paint job and less risk of corrosion occurrence. This is because the EQp creates a feathered profile with smooth edges, which generates proper paint adhesion. Surface preparation with pressure washers gives you a straight/deep cut, where water can get stuck. Rust will occur much faster when this happens.
Technical requirements
- An air network with tubes with a min. 1-1,5 inch diameter.
- A 37 Kw Oil-injected Screw Compressors or a more powerfull alternative.
- Working Air Receivers to prevent leakage, are beneficial.
- An air dryer to remove oil from the air network is recommended.
- Blast media (e.g. Garnet, crushed glass,...)
- A 1 inch blast hose is recommended to provide a larger blast pattern.
- A water connection or an external water tank.
Ask a Question or Get a Free Quote
EcoQuip 2 EQp - Powerful. Portable. Professional.
Graco’s new EcoQuip2 EQp is not only easy to use, but portable enough to take from one job to another. In addition, this affordable option in vapour abrasive blast equipment reduces dust by up to 92% less than traditional dry blasting.
The machine uses very little water, making containment and cleanup of debris simple and less messy than power/pressure washers or other dry and wet abrasive blasting technologies.