- 현장 이동성이 뛰어나고 접근이 어려운 공간에 이상적인 소형 제품
- 1인 작업으로 시간과 비용 절감
- 기존의 도장 사업에 추가 운영 가능
- 다목적성 - 콜드 스프레이에서 핫 스프레이 및 폼 도포로 전환 가능
- 1회용 폼 시스템에 비해 도료 비용 30% 절감
리액터 E-10 전기 폼 및 폴리우레아 혼합장치
소규모 폴리우레탄 폼 또는 폴리우레아 프로젝트나 터치업용 - 분당 최대 12 lb(5.4 kg) 도포
Graco의 리액터 E-10은 성능을 희생하지 않고도 협소한 공간에서 소규모 작업을 할 수 있는 즉시 사용이 가능한 소형 시스템입니다. 리액터 E-10 도장기는 이액형 도장, 조인트 채움 및 터치업 작업에 이상적입니다. 설정 및 운영이 간편한 스마트 컨트롤을 제공하는 E-10은 어떤 혼합 장치에도 잘 어울리는 보조 장비입니다.

좋은 결과를 제공하는 즉시 사용 가능한 소형 제품!
- 낮은 전력 소비 및 표준 콘센트 연결 가능
- 단 하나의 노브로 제어 가능한 직관적 시작, 중지 및 디지털 온도 디스플레이
- 시스템 압력 균형을 빠르고 쉽게 맞출 수 있는 압력 균형 밸브
- 균형 잡힌 혼합으로 압력 변화를 제거하여 일정한 스프레이 패턴 유지
- 수리가 간편한 유체 섹션으로 인한 유지보수 필요 감소 및 생산성 증대
- 생산성을 향상시키고 운영 비용을 줄여주는 전기 모터
- 분사율을 보여주는 독립형 반투명 도료 탱크
- 히터와 호스는 최대 2000w(와트)의 전력으로 도료를 순환 예열
매뉴얼
자료
Reactor E-10 | |
Maximum Fluid Working Pressure |
2000 psi
140 bar, 14 MPa
|
Maximum Fluid Temperature |
160°F
71°C
|
Maximum Ambient Temperature |
110°F
43°C
|
Maximum Output at 340 cycles/min |
12 lb/min
5.4 kg/min
|
Output per Cycle (A and B) |
0.00352 gal
0.0133 liter
|
Overpressure Relief |
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
|
Weight (approximately, depending on model) |
160 lb
72 kg
|
Wetted Parts |
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
|
Electrical Requirements | |
Model AP9570, CS9570: |
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
|
Model AP9571, CS9571: |
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
|
Model AP9572, CS9572: |
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
|
Model 249806: |
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
|
Model 249808: |
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
|
Generator Size (for Reactor E-10 only) | |
Heated: |
5000 W minimum
5000 W minimum
|
Nonheated: |
2500 W minimum
2500 W minimum
|
Heater Power | |
120V models: |
850 W each; 1700 W total
850 W each; 1700 W total
|
240V models: |
1000 W each; 2000 W total
1000 W each; 2000 W total
|
Sounds Pressure | |
Fast Circulation Mode: |
78.7 dB(A)
78.7 dB(A)
|
At 2000 psi (14 MPa, 140 bar), 0.72 gpm (2.7 lpm): |
84.5 dB(A)
84.5 dB(A)
|
Sound Power, measured per ISO 9416–2 | |
Fast Circulation Mode: |
88.6 dB(A)
88.6 dB(A)
|
At 2000 psi (14 MPa, 140 bar, 0.72 gpm (2.7 lpm): |
94.4 dB(A)
94.4 dB(A)
|
Tank Capacity (nominal) |
7 gal
26.5 liters
|
Fluid Outlets | |
Component A (ISO): |
-5 JIC male
-5 JIC male
|
Component B (RES): |
-6 JIC male
-6 JIC male
|
Fluid Circulation Ports | |
Component A (ISO): |
-5 JIC male
-5 JIC male
|
Component B (RES): |
-6 JIC male
-6 JIC male
|
Air Inlet |
1/4 in quick-disconnect industrial type pin fitting
1/4 in quick-disconnect industrial type pin fitting
|
Air Outlet |
1/4 npsm(m)
1/4 npsm(m)
|
Gun Compressed Air Requirements | |
Fusion Gun (purge air and operating air): |
4 scfm
0.112 m³/min
|
2K Ultra-Lite Gun with disposable mixer kit, with air spray valve fully open: |
14 scfm
0.392 m³/min
|
2K Ultra-Lite Gun with joint fill kit: |
2 scfm
0.056 m³/min
|
Hose Markings | |
A Side |
Red
Red
|
B Side |
Blue
Blue
|
부속품
관련 제품
-
Reactor 2 E-30
Next generation technology for spray foam insulation and polyurea
-
Reactor 2 E-30i
Turnkey system for spray foam insulation and coating - applies up to 30 lb (13.6 kg) per minute
-
Reactor E-10hp
Entry-level system for pure and hybrid polyurea coatings
-
Reactor E-8p for Flooring
For small to mid-sized no-heat joint fill applications
-
리액터 A-25
폼 단열재 분사용 - 분당 최대 25 lb(11.4 kg) 도포
-
리액터 E-20 및 E-30
중-고출력 폼 단열 분사용 - 분당 최대 30 lb(13.6 kg) 도포
-
리액터 E-8p
스프레이 폴리우레탄 폼 공기 실링 애틱 및 림 조이스트용