Graco Inc.

Pacotes de Endurecimento Rápido XP50  Pulverização de dois componentes de modo fácil e acessível

Otimizado para revestimentos de endurecimento rápido

Onde comprarSolicitar informações
Share |

Uma alternativa inteligente para lidar com misturas manuais

Os Pulverizadores com Componentes Múltiplos XP da Graco foram projetados para bombear, mesclar e atomizar revestimentos de alta viscosidade e com alta concentração de sólidos com resultados superiores. Quando você deixar de usar a mistura manual, você descobrirá que o XP oferece um excelente retorno de investimento ao reduzir o desperdício de material e usar menos solvente para limpeza.

Pacotes de Endurecimento Rápido XP 50

  • Otimizados para revestimentos híbridos de secagem rápida e de uretano elastomérico
  • Incluem um coletor de mistura modificada (em geral removível) com calibres de pressão de fluidos e válvulas de solventes tanto para o material A como para o material B, mais uma linha de mistura estática mais curta que 10 pés para a pistola de pulverização. A mangueira aquecida é opcional.
  • Ideal para substituir os pacotes de endurecimento rápido King Hydra-Cat™ da Graco


Experimente a calculadora de ROI (Retorno de Investimento) na aba Recursos e veja quanto você pode economizar.

Deixe de usar a mistura manual e veja os benefícios

2010 Graco Midwest Tank
  • Redução do desperdício de materiais
  • Chega de jogar fora no final do dia o material mesclado não usado
  • Economize dinheiro ao usar menos solvente para limpeza
  • Qualidade de material constante - chega de ter que adivinhar e de erros de cálculo na medição de material
  • Fácil de operar - mínimo treinamento necessário
  • Custos reduzidos de manutenção
  • Avaliado para 7250 psi (500 bar, 50 MPa) para manipular materiais viscosos e mangueiras de grande extensão

Manuais

Bibliografia

Outros recursos

Ver valores em unidades métricas. Ver valores em unidades dos Estados Unidos.



XP and XP-h Proportioners
Maximum Fluid Working Pressure
See Models section in instruction manual.
See Models section in instruction manual.
Maximum Air/Hydraulic Oil Working Pressure
See Models section in instruction manual.
See Models section in instruction manual.
Combined Fluid Output (cc/cycle)
See Models section in instruction manual.
See Models section in instruction manual.
Pressure Ratio
See Models section in instruction manual.
See Models section in instruction manual.
Fluid Flow at 40 cpm
See Models section in instruction manual.
See Models section in instruction manual.
Hydraulic Fluid Consumption (XP-h models only)
0.2 gallons per cycle
0.76 liters per cycle
Air inlet size
3/4 npsm(f)
3/4 npsm(f)
Maximum air pressure supply to the system
175 psi
12 bar, 1 MPa
Fluid pump inlets without hoppers
1-1/4 in. npsm(m)
1-1/4 in. npsm(m)
Fluid gauge manifold outlets
1/2 in. npt(f)
1/2 in. npt(f)
Fluid mix manifold inlets
1/2 in. npt(f) ball valves
1/2 in. npt(f) ball valves
Mix manifold material outlet
1/2 in. npt(f)
1/2 in. npt(f)
Maximum feed pressure from remote source
250 psi
17 bar, 1.7 MPa
Sound pressure
86 dBA at 100 psi
7 bar, 0.7 MPa
Sound power
98 dBA at 100 psi
7 bar, 0.7 MPa
Maximum Storage Time
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
Maximum Lifetime
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
Power Efficiency Factor (XP70)
75 cu. ft compressed air/1 gallon sprayed material at 100 psi
2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa)
Air consumption per 1 gallon (3.78 l) of flow
XP70
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
XP50
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
XP35
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
Filtration
Air inlet filtration
40-micron filter/separator included
40-micron filter/separator included
XP pump outlets
30 mesh
30 mesh
XTR Spray Gun
60 mesh
60 mesh
Fluid Viscosity Range
Gravity feed with 7 gallon (26 liter) hoppers
200 to 20,000 cps (pourable)
200 to 20,000 cps (pourable)
Pressure feed
Any viscosity that will not require feed pressure more than 15% of outlet pressure
Any viscosity that will not require feed pressure more than 15% of outlet pressure
Environmental Rating (Indoor/outdoor)
Hazardous Areas
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
Ambient Temperature Range
Operating
40-130°F
4-54°C
Storage
30-160°F
-1-71°C
Maximum Fluid Temperature
160°F
71°C
Wetted materials
Housings and manifolds
Carbon steel with electroless nickel plating
Carbon steel with electroless nickel plating
Miscellaneous parts
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
Pump packings
Carbon filled PTFE, proprietary UHMWPE
Carbon filled PTFE, proprietary UHMWPE
Flush pump suction tube
Aluminum
Aluminum
Hoses
Nylon core
Nylon core
Weight
Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers
575 lb
261 kg
Full XP-h System with heaters, solvent flush pump, and hoppers
600 lb
273 kg
Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers
425 lb
193 kg
Bare XP-h System with no heaters, solvent flush pump, or hoppers
450 lb
204 kg
XP35, XP50, or XP70 Pump only
286 lb
130 kg
XP-h Pump only
290 lb
132 kg