Graco Inc.

Viscon Fluid Heaters  High performance fluid heaters

Provides excellent temperature conditioning for high solids coatings and high viscosity materials

مكان الشراءطلب معلومات
مشاركة |

Graco's Viscon heaters maintain optimal temperatures to provide consistent control of fluid viscosity. With a wide temperature operating range, Viscon heaters are excellent for any coating, sealant, adhesive or lubricant you need to pump.

Viscon HF High Flow Fluid Heaters
- Designed for high flow rates, with more power for faster material heating

Viscon HF Fluid Heaters for Explosive Atmospheres
- Developed to handle the highest viscosity coatings such as 100% solids epoxies coatings and epoxy fireproofing materials

Viscon HP High Output Fluid Heaters
- Offers high pressure (7250 psi/500 bar) for use with most pumps


Viscon HF Heater with Manual Thermostat Control


Viscon HF High Flow Fluid Heater

  • Spiral passages provide three times the flow rate of standard Viscon heaters
  • Efficient and powerful for faster material heating - gets the job done faster
  • Available in manual thermostat or externally controlled versions
  • Excellent for high solids coatings and protective coatings materials
  • Easy to clean and maintain
  • 7250 psi (500 bar, 50 MPA)
  • Temperature operating range: 84 to 219°F (29 to 104°C)
Viscon_HF_Ex


Viscon HF Fluid Heaters for Explosive Atmospheres

  • The patent-pending design has a triple-path spiral core that can be easily disassembled for cleaning.
  • Increased flow capacity: The Viscon HF has over three (3) times more flow capacity compared to the standard Viscon HP heaters.  
  • Increased heat capacity: The Viscon HF heaters have 35% more wattage; 5400 watts compared to 4000W for the standard Viscon HP heaters.
  • Available in manual thermostat or externally controlled versions.
  • Cleanable and replaceable fluid core – repair instead of replace.
  • 7250 psi (500 bar, 50 MPA) pressure rating – handles the highest pressure rating of Graco protective coating sprayers.
  • Temperature operating range: 84 to 219°F (29 to 104°C)
  • Same mounting configuration as standard Viscon HP heaters – Easy to retrofit onto existing equipment.

Viscon Std Heater



Viscon HP High Output Fluid Heater

  • Higher pressure for use with most pumps
  • Excellent for high solids coatings, adhesives or resins
  • 7/16 in (11 mm) diameter fluid passages
  • Stainless steel design
  • Available in standard or explosive atmosphere versions
  • 7250 psi (500 bar, 50 MPa)
  • Temperature operating range: 84 to 219°F (29 to 104°C)

أدلة المستخدم

الأدب

عرض القيم بالقيم المترية. عرض القيم بوحدات الولايات المتحدة.

Viscon HF
U.S.
Metric
Metric
The heater can be used in the following environmental conditions: indoor use, 99% maximum relative humidity, pollution degree 2, installation category II, maximum ambient temperature 135° F (57° C).
Maximum Working Pressure
7250 psi (50 MPa, 500 bar)
7250 psi (50 MPa, 500 bar)
Voltage / Wattage / Current*
See Models on page 2.
See Models on page 2.
Fluid Passage Heat Transfer Area
210 in.² (1355 cm²)
210 in.² (1355 cm²)
Fluid Passage Dimensions (3 parallel paths)
Height: 0.41 in.
Height: 0.41 in.
Width: 0.32 in.
Length: 3 x 48 in.
Fluid Passage Equivalent Diameter
0.72 in. (18.3 mm)
0.72 in. (18.3 mm)
Thermometer Range
64 - 250°F (18 - 121°C)
64 - 250°F (18 - 121°C)
Wetted Parts
Stainless Steel, Anodized Aluminum, Electroless Nickel-Plated Steel, PTFE
Stainless Steel, Anodized Aluminum, Electroless Nickel-Plated Steel, PTFE
Temperature Operating Range
84 - 219°F (29 - 104°C)
84 - 219°F (29 - 104°C)
Weight
51 lb (23.2 kg)
51 lb (23.2 kg)
RTD (Model 262853 only)
1000 ohm, class B, 3-wire Connector: M8, 4-pin male
1000 ohm, class B, 3-wire Connector: M8, 4-pin male
Main supply fluctuation not to exceed 10%.