- Reduzierte Materialabfälle
- Kein Wegwerfen von nicht verwendetem gemischten Material am Ende des Arbeitstages
- Spart Geld durch weniger Lösungsmittel bei der Reinigung
- Gleichbleibende Materialqualität - kein Rätselraten oder menschliches Versagen beim Messen der Materialien
- Einfache Bedienung - minimale Schulung erforderlich
- Reduzierte Wartungskosten
- Ausgelegt für 50 MPa (500 bar, 7250 psi), um viskose Materialien und lange Schlauchlängen zu bewältigen
XP50 QuickSet-Pakete Mehrkomponenten-Spritzen - einfach und preiswert
Optimiert für schnelltrocknende Beschichtungen
Die intelligente Alternative zum manuellen Mischen
Die Graco XP Mehrkomponenten-Spritzgeräte wurden entwickelt, um hochviskose, hochfeste Beschichtungen mit erstklassigen Ergebnissen zu pumpen, zu mischen und zu zerstäuben. Wird vom Mischen per Hand umgestiegen, werden Sie schnell feststellen, dass die XP eine hervorragende Amortisation bietet, da Materialabfälle reduziert werden und weniger Lösungsmittel beim Reinigen verwendet wird.
XP50 QuickSet-Pakete
- Optimiert für schnelltrocknende Hydrid- und elastomere Urethan-Beschichtungen
- Umfasst einen modifizierten Mischverteiler (normalerweise extern befestigt) mit Materialdruckmessgeräten und Lösungsmittelventilen für A- und B-Material sowie eine kürzere statische Mischleitung von 10 ft an die Spritzpistole. Beheizter Schlauch ist optional.
- Idealer Ersatz für Graco King Hydra-Cat™ QuickSet-Pakete
Verwenden Sie den ROI-Rechner im Reiter „Ressourcen“, um zu sehen, wie viel Sie sparen können.
Vom Mischen per Hand umsteigen und die Vorteile erkennen

Handbücher
- 309524Y, Viscon HP High Pressure Fluid Heater, Instructions, Parts, English [andere sprachen]
- 312295K, XTR 5 und XTR 7 Airless Spritzpistole, Anleitung, Teile, Deutsch [andere sprachen]
- 3A1248G - Mix Manifold, Instructions-Parts, German [andere sprachen]
- 3A1034N - XP Proportioners, Instructions-Parts, German [andere sprachen]
- 3A0421B, Manual, Ratio Check Kit, Instructions, English (nur in Englisch)
- 309852E -Reactor Circulation and Return Tube Kits, English (nur in Englisch)
- 310863P, Manual, Feed and Solvent Flush Kits, Instructions and Parts, English [andere sprachen]
- 312455ZAH, Handbuch, Xtreme-Unterpumpen, Anleitung–Teileliste, Deutsch (noptc) [andere sprachen]
- 311486E, Manual, DataTrak Conversion Kit, Instructions, English [andere sprachen]
- 313629C, Merkur Pump Assembly, Instructions/Parts, German [andere sprachen]
- 312769F, Feed Pump Kits, XM, XP70, Instructions-Parts, US English (nur in Englisch)
- 3A0327L - Double Wall Hopper, Instructions-Parts, German [andere sprachen]
309524Y, Viscon HP High Pressure Fluid Heater, Instructions, Parts, English
312295K, XTR 5 und XTR 7 Airless Spritzpistole, Anleitung, Teile, Deutsch
3A1248G - Mix Manifold, Instructions-Parts, German
3A1034N - XP Proportioners, Instructions-Parts, German
310863P, Manual, Feed and Solvent Flush Kits, Instructions and Parts, English
312455ZAH, Handbuch, Xtreme-Unterpumpen, Anleitung–Teileliste, Deutsch (noptc)
311486E, Manual, DataTrak Conversion Kit, Instructions, English
313629C, Merkur Pump Assembly, Instructions/Parts, German
Literatur
- 350210DE XP™ [andere sprachen]
- 348546A Graco XP Pressure Monitor Kit Flyer (English) (nur in Englisch)
- 349329DE Ersatz- und Zubehörteile [andere sprachen]
- 349706DE Xtreme-Duty Rührwerk [andere sprachen]
- 300738ENEU SHIP & RIG BUILDING [andere sprachen]
349329DE Ersatz- und Zubehörteile
Andere Ressourcen
XP and XP-h Proportioners | |
Maximum Fluid Working Pressure | See Models section in instruction manual. See Models section in instruction manual. |
Maximum Air/Hydraulic Oil Working Pressure | See Models section in instruction manual. See Models section in instruction manual. |
Combined Fluid Output (cc/cycle) | See Models section in instruction manual. See Models section in instruction manual. |
Pressure Ratio | See Models section in instruction manual. See Models section in instruction manual. |
Fluid Flow at 40 cpm | See Models section in instruction manual. See Models section in instruction manual. |
Hydraulic Fluid Consumption (XP-h models only) | 0.2 gallons per cycle 0.76 liters per cycle |
Air inlet size | 3/4 npsm(f) 3/4 npsm(f) |
Maximum air pressure supply to the system | 175 psi 12 bar, 1 MPa |
Fluid pump inlets without hoppers | 1-1/4 in. npsm(m) 1-1/4 in. npsm(m) |
Fluid gauge manifold outlets | 1/2 in. npt(f) 1/2 in. npt(f) |
Fluid mix manifold inlets | 1/2 in. npt(f) ball valves 1/2 in. npt(f) ball valves |
Mix manifold material outlet | 1/2 in. npt(f) 1/2 in. npt(f) |
Maximum feed pressure from remote source | 250 psi 17 bar, 1.7 MPa |
Sound pressure | 86 dBA at 100 psi 7 bar, 0.7 MPa |
Sound power | 98 dBA at 100 psi 7 bar, 0.7 MPa |
Maximum Storage Time | 5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) 5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) |
Maximum Lifetime | Indefinite with recommended maintenance and periodic rebuilds for critical parts. Indefinite with recommended maintenance and periodic rebuilds for critical parts. |
Power Efficiency Factor (XP70) | 75 cu. ft compressed air/1 gallon sprayed material at 100 psi 2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa) |
Air consumption per 1 gallon (3.78 l) of flow | |
XP70 | 75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) 75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) |
XP50 | 60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) 60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) |
XP35 | 50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) 50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) |
Filtration | |
Air inlet filtration | 40-micron filter/separator included 40-micron filter/separator included |
XP pump outlets | 30 mesh 30 mesh |
XTR Spray Gun | 60 mesh 60 mesh |
Fluid Viscosity Range | |
Gravity feed with 7 gallon (26 liter) hoppers | 200 to 20,000 cps (pourable) 200 to 20,000 cps (pourable) |
Pressure feed | Any viscosity that will not require feed pressure more than 15% of outlet pressure Any viscosity that will not require feed pressure more than 15% of outlet pressure |
Environmental Rating (Indoor/outdoor) | |
Hazardous Areas | EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. |
Ambient Temperature Range | |
Operating | 40-130°F 4-54°C |
Storage | 30-160°F -1-71°C |
Maximum Fluid Temperature | 160°F 71°C |
Wetted materials | |
Housings and manifolds | Carbon steel with electroless nickel plating Carbon steel with electroless nickel plating |
Miscellaneous parts | Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics |
Pump packings | Carbon filled PTFE, proprietary UHMWPE Carbon filled PTFE, proprietary UHMWPE |
Flush pump suction tube | Aluminum Aluminum |
Hoses | Nylon core Nylon core |
Weight | |
Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers | 575 lb 261 kg |
Full XP-h System with heaters, solvent flush pump, and hoppers | 600 lb 273 kg |
Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers | 425 lb 193 kg |
Bare XP-h System with no heaters, solvent flush pump, or hoppers | 450 lb 204 kg |
XP35, XP50, or XP70 Pump only | 286 lb 130 kg |
XP-h Pump only | 290 lb 132 kg |
-
Dachbeschichtungen
-
Rostschutz
-
Schiffbau und Seefahrt
-
Schutzschichten für Brücken
-
Herstellung und Reparatur von Schienenfahrzeugen
-
Towers for Wind Turbines
-
Rohr- und Behälterbeschichtungen
-
Lackierung von Baustählen
-
Schutzanstriche von Wassertürmen
-
Abwasseraufbereitung
-
Überholung von Schächten und Abwasserkanälen
-
Sekundärer Überlaufschutz
-
Korrosionsschutz
-
Offshore-Anlagen
Zubehör
-
Pistolenverteiler
Zwei Spritzpistolen mit einem XP-Spritzgerät verwenden
-
T1, T2 und T3 Transferpumpen
Ideal für das Bewegen von A- und B-Materialien an Reactor-Dosierer
-
Viscon Materialheizungen
Bietet hervorragende Temperaturregelung für hochfeste Beschichtungen und hochviskose Materialien
-
XTR-5 und XTR-7
Airless-Spritzpistolen für Schutzanstriche
-
Xtreme-Duty Schlauch
Für Hochdruck-Spritzanwendungen