Graco Inc.

Pacchetti a presa rapida XP50  La spruzzatura bicomponente resa semplice e conveniente

Ottimizzati per i rivestimenti a presa rapida

Dove comprareRichiesta di informazioni

Un'alternativa intelligente alla miscelazione manuale

Lo spruzzatore multicomponente XP Graco è progettato per pompare, miscelare e nebulizzare materiali ad alto contenuto di solidi e ad alta viscosità con risultati superiori. Se provenite dalla miscelazione manuale, scoprirete che XP offre un rendimento degli investimenti straordinario, riducendo lo spreco di materiale grazie al minore utilizzo di solventi di pulizia.

Pacchetti a configurazione rapida XP50

  • Ottimizzati per rivestimenti in uretano elastomerico e ibrido a presa rapida
  • Includono un collettore di miscelatore modificato (in genere non montato) con manometri del fluido e valvole del solvente per i materiali A e B, nonché una linea di miscelazione statica più corta da 3,05 m (10 ft) alla pistola a spruzzo. Flessibile riscaldato opzionale.
  • Sostituto ideale dei pacchetti a presa rapida King Hydra-Cat™ Graco


Provate il calcolatore ROI nella scheda Risorse per vedere quanto potete risparmiare.

Se venite dalla miscelazione manuale ne proverete i benefici

2010 Graco Midwest Tank
  • Riduce lo spreco di materiale
  • Non dovrete più gettare il materiale inutilizzato a fine giornata
  • Risparmiate denaro usando meno solvente di pulizia
  • Qualità costante del materiale: basta incertezze o errori umani nella misurazione del materiale
  • Facile da usare: richiede una formazione minima
  • Spese di manutenzione ridotte
  • Dimensionato per 500 bar (50 MPa, 7250 psi) per gestire materiali viscosi e tubi flessibili lunghi

Manuali



XP and XP-h Proportioners
Maximum Fluid Working Pressure
See Models section in instruction manual.
See Models section in instruction manual.
Maximum Air/Hydraulic Oil Working Pressure
See Models section in instruction manual.
See Models section in instruction manual.
Combined Fluid Output (cc/cycle)
See Models section in instruction manual.
See Models section in instruction manual.
Pressure Ratio
See Models section in instruction manual.
See Models section in instruction manual.
Fluid Flow at 40 cpm
See Models section in instruction manual.
See Models section in instruction manual.
Hydraulic Fluid Consumption (XP-h models only)
0.2 gallons per cycle
0.76 liters per cycle
Air inlet size
3/4 npsm(f)
3/4 npsm(f)
Maximum air pressure supply to the system
175 psi
12 bar, 1 MPa
Fluid pump inlets without hoppers
1-1/4 in. npsm(m)
1-1/4 in. npsm(m)
Fluid gauge manifold outlets
1/2 in. npt(f)
1/2 in. npt(f)
Fluid mix manifold inlets
1/2 in. npt(f) ball valves
1/2 in. npt(f) ball valves
Mix manifold material outlet
1/2 in. npt(f)
1/2 in. npt(f)
Maximum feed pressure from remote source
250 psi
17 bar, 1.7 MPa
Sound pressure
86 dBA at 100 psi
7 bar, 0.7 MPa
Sound power
98 dBA at 100 psi
7 bar, 0.7 MPa
Maximum Storage Time
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
5 years (To maintain original performance, replace soft seals after 5 years of inactivity.)
Maximum Lifetime
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
Indefinite with recommended maintenance and periodic rebuilds for critical parts.
Power Efficiency Factor (XP70)
75 cu. ft compressed air/1 gallon sprayed material at 100 psi
2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa)
Air consumption per 1 gallon (3.78 l) of flow
XP70
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa)
XP50
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa)
XP35
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa)
Filtration
Air inlet filtration
40-micron filter/separator included
40-micron filter/separator included
XP pump outlets
30 mesh
30 mesh
XTR Spray Gun
60 mesh
60 mesh
Fluid Viscosity Range
Gravity feed with 7 gallon (26 liter) hoppers
200 to 20,000 cps (pourable)
200 to 20,000 cps (pourable)
Pressure feed
Any viscosity that will not require feed pressure more than 15% of outlet pressure
Any viscosity that will not require feed pressure more than 15% of outlet pressure
Environmental Rating (Indoor/outdoor)
Hazardous Areas
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated.
Ambient Temperature Range
Operating
40-130°F
4-54°C
Storage
30-160°F
-1-71°C
Maximum Fluid Temperature
160°F
71°C
Wetted materials
Housings and manifolds
Carbon steel with electroless nickel plating
Carbon steel with electroless nickel plating
Miscellaneous parts
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics
Pump packings
Carbon filled PTFE, proprietary UHMWPE
Carbon filled PTFE, proprietary UHMWPE
Flush pump suction tube
Aluminum
Aluminum
Hoses
Nylon core
Nylon core
Weight
Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers
575 lb
261 kg
Full XP-h System with heaters, solvent flush pump, and hoppers
600 lb
273 kg
Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers
425 lb
193 kg
Bare XP-h System with no heaters, solvent flush pump, or hoppers
450 lb
204 kg
XP35, XP50, or XP70 Pump only
286 lb
130 kg
XP-h Pump only
290 lb
132 kg