Graco Inc.

Active Surge Suppressor  Dampen pump pulsation for consistent finish quality

Reduces pulsation for consistent material delivery and uniform spray pattern

구매처정보 요청
공유 |

'Set and Forget' Pulsation Minimization

Minimize pulsation on factory paint circulation lines with Graco's active surge suppressor. Once you set it up, you can forget about manual adjustments.

  • Active air pressure compensation makes periodic air pressure checks unnecessary.
  • Automatic self-adjustment removes the need to manually adjust air pressure inside the surge suppressor when target fluid pressure changes.
Active Surge Suppression
  • Shop air compatibility: Suppressor connects to compressed air lines already installed in most plants.
  • Good flush-ability: Fluid section has an optimized flow path that flushes cleanly and thoroughly in between colors.
  • Improved failure mode: Check valve prevents paint from leaking out if a diaphragm ruptures.
Safe space with easy installation, mount anywhere in any position.


  • Save space with easy installation
  • Mount directly onto pump, wall or floor.
  • Install in down or up position.

What are surge suppressors?

Also called “surge tanks,” surge suppressors are used in paint circulation systems to remove pressure pulsations from the supply pump.

During a pump changeover, a very brief but undesirable pressure pulsation occurs. Adding a surge suppressor can eliminate the pressure pulsation. 
 

시스템 내의 압력 변화를 줄일 필요가 있으십니까? Graco의 서지 억제기는 고객의 프로세스 요구사항을 충족하도록 제작되었습니다.

Benefits of EQp

Manufacturers concerned about paint line pulsation can set and forget the active surge suppressor. It automatically adjusts itself for peak performance in changing conditions. Once you set it up, you can forget about manual adjustments.

 

  • Works off shop air, eliminating need for and extra cost of high pressure charge air
  • Flushes cleanly and thoroughly in between colors
  • Saves space with pump-mount configuration
  • Backup seal keeps paint from leaking out, in case of diaphragm rupture

 

측정 단위로 값 보기. 미국 달러로 가격 보기.

Surge Tank Model 238986
Maximum Fluid Working Pressure
300 psi
2.1 MPa, 21 bar
Maximum Gas Charge Pressure
300 psi
2.1 MPa, 21 bar
Maximum Flow Rate (Maximum flow rates are recommended maximums for peak performance, Exceeding these values reduces the surge tank’s ability to dampen pulsation)
20 gpm
76 lpm
Maximum Operating Temperature
120° F
50° C
Wetted Parts
304 & 316 Stainless Steel, PTFE
304 & 316 Stainless Steel, PTFE
Surge Tank Model 238987
Maximum Fluid Working Pressure
300 psi
2.1 MPa, 21 bar
Maximum Gas Charge Pressure
300 psi
2.1 MPa, 21 bar
Maximum Flow Rate (Maximum flow rates are recommended maximums for peak performance, Exceeding these values reduces the surge tank’s ability to dampen pulsation)
20 gpm
76 lpm
Maximum Operating Temperature
120° F
50° C
Wetted Parts
304 & 316 stainless steel, PTFE
304 & 316 stainless steel, PTFE
Surge Tank Model 238988
Maximum Fluid Working Pressure
300 psi
2.1 MPa, 21 bar
Maximum Gas Charge Pressure
300 psi
2.1 MPa, 21 bar
Maximum Flow Rate (Maximum flow rates are recommended maximums for peak performance, Exceeding these values reduces the surge tank’s ability to dampen pulsation)
20 gpm
76 lpm
Maximum Operating Temperature
120° F
50° C
Wetted Parts
304 & 316 stainless steel, PTFE
304 & 316 stainless steel, PTFE
Surge Tank Model 233736
Maximum Fluid Working Pressure
360 psi
2.5 MPa, 25 bar
Maximum Air Inlet Pressure
218 psi
1.5 MPa, 15 bar
Maximum Flow Rate (Maximum flow rates are recommended maximums for peak performance, Exceeding these values reduces the surge tank’s ability to dampen pulsation)
Tank volume is 0.4 gal, Fluid does not flow through tank
Fluid does not flow through tank
Maximum Operating Temperature
176° F
80° C
Wetted Parts
Stainless steel, PTFE
Stainless steel, PTFE
Surge Tank Model 218509
Maximum Fluid Working Pressure
600 psi
4.2 MPa, 42 bar
Maximum Gas Charge Pressure
600 psi
4.2 MPa, 42 bar
Maximum Flow Rate (Maximum flow rates are recommended maximums for peak performance, Exceeding these values reduces the surge tank’s ability to dampen pulsation)
20 gpm
76 lpm
Maximum Operating Temperature
120° F
50° C
Wetted Parts
Carbon steel, electroless nickel-plated steel, UHMW polyethylene, fluoroelastomer, PTFE
Carbon steel, electroless nickel-plated steel, UHMW polyethylene, fluoroelastomer, PTFE
Surge Tank Model 220157
Maximum Fluid Working Pressure
600 psi
4.2 MPa, 2 bar
Maximum Gas Charge Pressure
600 psi
4.2 MPa, 42 bar
Maximum Flow Rate (Maximum flow rates are recommended maximums for peak performance, Exceeding these values reduces the surge tank’s ability to dampen pulsation)
15 gpm
57 lpm
Maximum Operating Temperature
120° F
50° C
Wetted Parts
304 and 17–4 PH stainless steel, UHMW polyethylene, fluoroelastomer, PTFE, tungsten carbide
304 and 17–4 PH stainless steel, UHMW polyethylene, fluoroelastomer, PTFE, tungsten carbide