- Minder materiaalverspilling
- U hoeft aan het einde van de dag dus nooit meer ongebruikt materiaal weg te gooien
- Spaar geld door minder oplosmiddelen voor het reinigen te gebruiken
- Consistente materiaalkwaliteit - geen giswerk of menselijke fouten meer bij het afpassen van materialen
- Eenvoudig te bedienen - minimale training vereist
- Lagere onderhoudskosten
- Geschikt voor 7250 psi (500 bar, 50 MPa) om hoog-viskeuze materialen en lange slangen aan te kunnen
XP50-pakketten voor snel uitharden Tweecomponentenmaterialen spuiten wordt eenvoudig en voordelig
Geoptimaliseerd voor coatings die snel uitharden
Een slim alternatief voor handmatig mengen
Graco XP-spuittoestellen voor meercomponentenmaterialen zijn bedoeld voor het pompen, vermengen en spuiten van hoog-viskeuze materialen met een superieure afwerkingskwaliteit. Als u het met de hand mengen verlaat, zult u zien dat de XP buitengewoon rendabel werkt door de materiaalverspilling te beperken en door minder reinigings-/oplosmiddel te gebruiken
XP 50-pakketten voor snel uitharden
- Geoptimaliseerd voor hybride en elastomerische urethaancoatings die snel uitharden
- Bevatten een aangepaste mengspruitstuk (meestal verwijderbaar gemonteerd) met vloeistofdrukmeters en oplosmiddelkleppen voor zowel A- als B-materiaal, plus een kortere ca. 3 meter lange statische mengleiding naar het spuitpistool. De verwarmde slang is optioneel.
- Ideale vervanger voor de Graco King Hydra-Cat™ pakketten voor snel uitharden
Probeer de ROI-calculator in het tabblad Resources uit en zie hoeveel u kunt besparen.
Stop met handmatig mengen en zie de voordelen

Handleidingen
- 309524Z, Viscon HP High Pressure Fluid Heater, Instructions, Parts, English [overige talen]
- 312138K, XTR 5 and XTR 7 airless spuitpistool, Instructies, onderdelen, Nederlands [overige talen]
- 3A1247G - Mix Manifold, Instructions-Parts, Dutch [overige talen]
- 3A0420ZAG, Manual, XP and XP-h Proportioners Operation, Repair, and Parts, English [overige talen]
- 3A0421B, Manual, Ratio Check Kit, Instructions, English (Alleen Engels)
- 309852E -Reactor Circulation and Return Tube Kits, English (Alleen Engels)
- 310863R, Manual, Feed and Solvent Flush Kits, Instructions and Parts, English [overige talen]
- 312452ZAH, Handboek, Xtreme-onderpompen, Instructies-onderdelenlijst, Nederlands(noptc) [overige talen]
- 311486E, Manual, DataTrak Conversion Kit, Instructions, English [overige talen]
- 313654L, Merkur-pompeenheid, Instructies en onderdelen, Dutch [overige talen]
- 312769G, Feed Pump Kits, XM, XP70, Instructions, English (Alleen Engels)
- 3A0325L - Double Wall Hopper, Instructions-Parts, Dutch [overige talen]
309524Z, Viscon HP High Pressure Fluid Heater, Instructions, Parts, English
312138K, XTR 5 and XTR 7 airless spuitpistool, Instructies, onderdelen, Nederlands
3A1247G - Mix Manifold, Instructions-Parts, Dutch
3A0420ZAG, Manual, XP and XP-h Proportioners Operation, Repair, and Parts, English
310863R, Manual, Feed and Solvent Flush Kits, Instructions and Parts, English
312452ZAH, Handboek, Xtreme-onderpompen, Instructies-onderdelenlijst, Nederlands(noptc)
311486E, Manual, DataTrak Conversion Kit, Instructions, English
313654L, Merkur-pompeenheid, Instructies en onderdelen, Dutch
Literatuur
- 350210NL XP- en XM-spuittoestellen [overige talen]
- 348546EN, Graco XP Pressure Monitor Kit Flyer (Alleen Engels)
- 349329NL Onderdelen en accessoires [overige talen]
- 349706NL Xtreme-Duty-roerwerk [overige talen]
- 300738NL SCHEEPS- EN PLATFORMBOUW [overige talen]
350210NL XP- en XM-spuittoestellen
349329NL Onderdelen en accessoires
Overige middelen
XP and XP-h Proportioners | |
Maximum Fluid Working Pressure | See Models section in instruction manual. See Models section in instruction manual. |
Maximum Air/Hydraulic Oil Working Pressure | See Models section in instruction manual. See Models section in instruction manual. |
Combined Fluid Output (cc/cycle) | See Models section in instruction manual. See Models section in instruction manual. |
Pressure Ratio | See Models section in instruction manual. See Models section in instruction manual. |
Fluid Flow at 40 cpm | See Models section in instruction manual. See Models section in instruction manual. |
Hydraulic Fluid Consumption (XP-h models only) | 0.2 gallons per cycle 0.76 liters per cycle |
Air inlet size | 3/4 npsm(f) 3/4 npsm(f) |
Maximum air pressure supply to the system | 175 psi 12 bar, 1 MPa |
Fluid pump inlets without hoppers | 1-1/4 in. npsm(m) 1-1/4 in. npsm(m) |
Fluid gauge manifold outlets | 1/2 in. npt(f) 1/2 in. npt(f) |
Fluid mix manifold inlets | 1/2 in. npt(f) ball valves 1/2 in. npt(f) ball valves |
Mix manifold material outlet | 1/2 in. npt(f) 1/2 in. npt(f) |
Maximum feed pressure from remote source | 250 psi 17 bar, 1.7 MPa |
Sound pressure | 86 dBA at 100 psi 7 bar, 0.7 MPa |
Sound power | 98 dBA at 100 psi 7 bar, 0.7 MPa |
Maximum Storage Time | 5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) 5 years (To maintain original performance, replace soft seals after 5 years of inactivity.) |
Maximum Lifetime | Indefinite with recommended maintenance and periodic rebuilds for critical parts. Indefinite with recommended maintenance and periodic rebuilds for critical parts. |
Power Efficiency Factor (XP70) | 75 cu. ft compressed air/1 gallon sprayed material at 100 psi 2.12 m³ compressed air/1 liter sprayed material at 7 bar (0.7 MPa) |
Air consumption per 1 gallon (3.78 l) of flow | |
XP70 | 75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) 75 scfm at 100 psi/gpm (2.12 m³/min at 7 bar, 0.7 MPa) |
XP50 | 60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) 60 scfm at 100 psi/gpm (1.7 m³/min at 7 bar, 0.7 MPa) |
XP35 | 50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) 50 scfm at 100 psi/gpm (1.42 m³/min at 7 bar, 0.7 MPa) |
Filtration | |
Air inlet filtration | 40-micron filter/separator included 40-micron filter/separator included |
XP pump outlets | 30 mesh 30 mesh |
XTR Spray Gun | 60 mesh 60 mesh |
Fluid Viscosity Range | |
Gravity feed with 7 gallon (26 liter) hoppers | 200 to 20,000 cps (pourable) 200 to 20,000 cps (pourable) |
Pressure feed | Any viscosity that will not require feed pressure more than 15% of outlet pressure Any viscosity that will not require feed pressure more than 15% of outlet pressure |
Environmental Rating (Indoor/outdoor) | |
Hazardous Areas | EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. EX II 2 G c IIA T2, NOTE: XP-h pump packages (284xxx) are not Ex rated. |
Ambient Temperature Range | |
Operating | 40-130°F 4-54°C |
Storage | 30-160°F -1-71°C |
Maximum Fluid Temperature | 160°F 71°C |
Wetted materials | |
Housings and manifolds | Carbon steel with electroless nickel plating Carbon steel with electroless nickel plating |
Miscellaneous parts | Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics Plated carbon steel, stainless steels, carbide, acetal, UHM-WPE, nylon, PTFE solvent resistant plastics |
Pump packings | Carbon filled PTFE, proprietary UHMWPE Carbon filled PTFE, proprietary UHMWPE |
Flush pump suction tube | Aluminum Aluminum |
Hoses | Nylon core Nylon core |
Weight | |
Full XP35, XP50, or XP70 System with heaters, solvent flush pump, and hoppers | 575 lb 261 kg |
Full XP-h System with heaters, solvent flush pump, and hoppers | 600 lb 273 kg |
Bare XP35, XP50, or XP70 system with no heaters, solvent flush pump, or hoppers | 425 lb 193 kg |
Bare XP-h System with no heaters, solvent flush pump, or hoppers | 450 lb 204 kg |
XP35, XP50, or XP70 Pump only | 286 lb 130 kg |
XP-h Pump only | 290 lb 132 kg |
-
Dakcoatings
-
Roestpreventie
-
Scheepsbouw en scheepvaart
-
Beschermende coatings brug
-
Bouw en reparatie van treinwagons
-
Towers for Wind Turbines
-
Het coaten van buizen en reservoirs
-
Coating van constructiestaal
-
Beschermende coatings van watertorens
-
Afvalwaterbehandeling
-
Renovatie van mangaten en rioleringssystemen
-
Secundaire insluitingslekpreventie
-
Corrosiepreventie
-
Boorplatformen
Toebehoren
-
Pistoolsplitter
Maakt het gebruik van twee spuitpistolen met één XP-spuitapparaat mogelijk
-
T1, T2 en T3 transferpompen
Ideaal voor het verplaatsen van A- en B-materiaal naar reactorverdelers
-
Viscon-vloeistofverwarmers
Zorgt voor een uitstekende temperatuurbehandeling bij coatings met een hoog gehalte vaste d...
-
XTR-5 en XTR-7
Airless spuitpistolen voor beschermende coatings
-
Xtreme-Duty-slang
Voor spuittoepassingen onder hoge druk