Graco Inc.

Dispensit 1052- en 1053-ventielen  Precisie-doseerventiel

Doseerstangventielen met positieve verdringing voor materialen met een lage tot hoge viscositeit

Waar te koopInformatie aanvragen

De positieve verdringerstangventielen model 1052 & 1053 zijn ontworpen voor volumetrische shot-naar-shot- (1052) of lijmstreepdosering (1053) van een brede keuze aan materialen.

  • Voor materialen met een lage tot hoge viscositeit met configuraties van diverse onderdelen die in aanraking komen met water
    voor abrasieve gevulde of corrosieve materialen
  • 1052 is een pneumatisch bediend ventiel met via een micrometer instelbare doseervolumes
    voor nauwkeurige, herhaalbare shotdosering
  • 1053 is een via een servomotor bediend ventiel voor het geprogrammeerd doseren van shots of lijmstrepen
  • Pneumatische en elektronische bedieningsinrichtingen kunnen worden ingebouwd voor geautomatiseerde toepassingen
  • Dosering via positieve verdringing
  • Brede keuze aan onderdelen die in contact komen met water

Dispensit 1053-10C
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
300°F
149°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
2 in.: 17.85 x 6.23 x 2.91 in
453 x 158 x 74 mm
453 x 158 x 74 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel

Dispensit 1052
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
150°F
65°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.600 cc
0.002 cc to 3.600 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 60 cycles per minute
Up to 60 cycles per minute
Dimensions (H x L x W), height to end of material inlet
16.13 x 5.52 x 2.75 in.
410 x 140 x 70 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 4 - 5 lb
1.81 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel

Dispensit 1053-10B
Maximum Ambient Temperature
110°F
43°C
Maximum Operating Temp
150°F
65°C
Maximum Outlet Fluid Working Pressure
2000 psi
14 MPa, 138 bar
Maximum Air Working Pressure
100 psi
0.7 MPa, 7 bar
Minimum Air Working Pressure
70 psi
480 kPa, 4.8 bar
Maximum Material Inlet Pressure
Metal Sleeves: 1200 psi
8 MPa, 83 bar
Plastic Sleeves: 400 psi
2.8 MPa, 28 bar
2.8 MPa, 28 bar
Supplied Air Requirements.
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected)
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
Maximum Cycle Rate (application dependent, heat required) .
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
2 in.: 17.85 x 6.23 x 2.91 in
453 x 158 x 74 mm
453 x 158 x 74 mm
Graco-supplied Feed System Assemblies (depends on selected options):
Smallest: 22.5 x 10 x 4 in.
572 x 254 x 102 mm
572 x 254 x 102 mm
Largest: 60 x 28 x 19 in.
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
Weight
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
Wetted Parts
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel