Graco Inc.

Elektrische Dyna-Star (EDS)  Elektrische Schmierpumpen und Zubehör

Elektropumpen für strapazierfähige automatische Schmier- und Übertragungssysteme.

Händlersuche
Teilen |

Die Dyna-Star-Hochdruckpumpe und die HF-24-VDC-Elektroschmierpumpe ergänzen unser Angebot der hydraulischen Pumpe Dyna-Star 10:1 und der pneumatischen Pumpe Fire-Ball 300 50:1. Nun stehen Ihnen drei Stromquellenoptionen für automatische Schmierungssysteme und Übertragungsanwendungen zur Verfügung.

Belastungsfähige Bau- und Bergbaugeräte benötigen stets eine frische Schmierung, um Verschmutzungen aus wichtigen Drehpunkten zu spülen. Ein automatisches Schmiersystem von Graco sorgt für die laufende Schmierung wichtiger Bauteile und hält diese ohne kostspielige Materialausfälle betriebsfähig.

  • Abschaltung Automatische Befüllung – mechanisches Abschalten der Füllpumpe für sichere und effiziente Wiederbefüllung
  • Graco Advantage Drive™ – strapazierfähiges Zahnradgetriebe – dauerhafte Schmierung
  • Rohr-in-Rohr-Pfadentlüftung und -füllung – sofort Fass zu Injektionssystem umrüsten
  • Entlüftungsventil direkt an der Pumpe angebracht – keine Halterungen oder zusätzliche Schläuche und Rohre mehr
  • Motorsteuerung – Geschwindigkeit und AMP-Steuerung
  • Kaltwetter-Leistung (-40 ºC)
  • Effizienterer Dichtungsaustausch
  • Optionale AC-DC-Umwandlerbox
  • Ermöglicht die Verwendung von 110–230 VAC für die Stromversorgung der 24-VDC-Dyna Star-Hochdruckpumpe und anderer Hochdruckpumpen
  • Die AC-DC-Umwandlerbox wird mit Befestigungs- und Verkabelungsequipment geliefert – für einfaches und flexibles Aufbauen
  • Der Fernfüllungsverteiler mit Belüftung (mit eingebautem Manometer) erlaubt die Platzierung der Einfüllöffnung an jeder gewünschten Stelle

Handbücher

Literatur

Werte in metrischen Einheiten anzeigen. Werte in US-Einheiten anzeigen.

Dyna-Star HP and HF Lubrication Pump
U.S.
Metric
Maximum Fluid Working Pressure
HF Models
3500 psi
24.1 MPa, 241 bar
HP Models
5000 psi
34.47 MPa, 344 bar
Electrical Requirements
All Models
24VDC
24VDC
Wire Terminal AWG Size for Control Board
24 to 10 AWG
24 to 10 AWG
Input Voltage Range
24 VDC
18 to 32 VDC
18 to 32 VDC
ON/OFF Signal Voltage Range and Current
Voltage Range
5 to 32 VDC
5 to 32 VDC
Drive Resistance
1.1K
1.1K
Peak Operating Current
24 VDC
35A
35A
Peak Power
24 VDC
720W
720W
Pump Output
HF Models
See Performance Charts in manual
See Performance Charts in manual
HP Models
See Performance Charts in manual
See Performance Charts in manual
Weight - Pump Only
35 - 60 lb Tank / Reservoir
50 lb.
22.7 kg
90 - 120 lb Tank / Reservoir
55 lb.
25.0 kg
400 lb Tank / Reservoir
0 lb.
27.2 kg
Wetted Parts
Pump Wetted Parts
steel, polyurethane, acetal, buna-N, aluminum, polyester elastomer
steel, polyurethane, acetal, buna-N, aluminum, polyester elastomer
Operating Temperature
HP Models
-40° to 149°F
–40° to 65°C
HF Models
14° to 149°F
-10° to 65°C
Storage Temperature HP and HF Models
-40° to 149°F
–40° to 65°C
Humidity Level
90%
90%
IP Rating
IP69K
IP69K
Audible Sound Pressure*
1000 psi (6.89 MPa, 58.95 bar) Models
70.7 dB(A)
70.7 dB(A)
2000 psi (13.79 MPa, 137.9 bar) Models
71.4 dB(A)
71.4 dB(A)
3000 psi (20.68 MPa, 206.84 bar) Models
71.4 dB(A)
71.4 dB(A)
4000 psi (27.58 MPa, 275.79 bar) Models
71.2 dB(A)
71.2 dB(A)
5000 psi (34.47 MPa, 374.74 bar) Models
70.6 dB(A)
70.6 dB(A)
Cable
Cable Gland Thread
M25
M25
Cable Range
0.36 - 0.64 in.
9 - 16 cm
*Sound power was measured per ISO-9614-2.

Dyna-Star® HP Vent Valve Kit
Maximum working pressure*
3500 psi
24.1 MPa, 241 bar
*Dyna-Star HP Pump models are rated for 5000 psi (34.47 MPa, 344 bar) maximum working pressure, however, when a vent valve is installed on the HP pump, the maximum working pressure must be reduced to 3500 psi (24.1 MPa, 241 bar).
Inlet/Outlet Sizes
Outlet (marked “0”)
3/8 in. NPT(f)
3/8 in. NPT(f)
Inlet (refill-marked “1”)
3/8 in. NPT(f)
3/8 in. NPT(f)
Pressure Relief Valve
Factory set pressure
4000 psi ± 250 psi
27 MPA, 275 bar ± 10%
Reset pressure
80% of set pressure
80% of set pressure
Relief Rate (Flow capability depends on viscosity, type of fluid, temperature, etc.)
0.1 gallons/minute @ 3500 psi
0.4 liters/minute @ 24.1 MPa, 241 bar
Solenoid Valve
Flow (Flow capability depends on viscosity, type of fluid, temperature, etc.)
Up to 0.2 gallons/minute, 40 cu. in./minute
0.65 liters /minute
Wetted parts
zinc plated steel, carbon steel, aluminum, fluoroelastomer, polyurethane
zinc plated steel, carbon steel, aluminum, fluoroelastomer, polyurethane
Weight
4.0 lbs
1.8 kg
IP rating
IP65K
IP65K
Solenoid Coil: Resistance (DC) (Ohms)
@ 68°F
@20°C
24 VDC
28.8
0.83

Auto-Fill Shutoff Valve for Dyna-Star® HP or HF Pump
Maximum working pressure*
5000 psi
34.4 MPa, 344 bar
Inlet/Outlet Sizes
Outlet (marked “0”)
3/8 in. NPT(f)
3/8 in. NPT(f)
Inlet (refill-marked “1”)
3/8 in. NPT(f)
3/8 in. NPT(f)
Maximum flow
2 gallons/minute
7.6 liters/minute
Wetted Parts
Valve
neoprene rubber, zinc plated parts, stainless steel, chrome plated pats, plastic acetal
neoprene rubber, zinc plated parts, stainless steel, chrome plated pats, plastic acetal
Seal
fluorocarbon
fluorocarbon
Temperature
Working temperature
-13°F to 122°F
-25°C to 50°C

Dyna-Star® HP Pump System
Maximum working pressure*
3500 psi
241 bar, 24.1 MPa
*Dyna-Star HP pump models are rated for a maximum working pressure of 5000 psi (344 bar, 34.47 MPa), however, when a vent valve is installed on the HP pump, the maximum working pressure must be reduced to 3500 psi (344 bar, 34.47 MPa).
Reservoir overflow port size
1/2 inch NPT
1/2 inch NPT
Reservoir fill port size
1/2 inch NPT
1/2 inch NPT
Lubricant outlet port size
3/8 inch NPT(f)
3/8 inch NPT(f)
Reservoir wetted parts
steel, buna-n rubber
steel, buna-n rubber
Pump wetted parts
See manual 332514, Dyna-Star HP and HF Pump
See manual 332514, Dyna-Star HP and HF Pump
Vent Valve wetted part
See manual 332519, Dyna-Star HP and HF Vent Valve Kit
See manual 332519, Dyna-Star HP and HF Vent Valve Kit
Grease Capacity
Models 77X101, 77X103, 77X105
90 lb.
41 kg
Models 77X100, 77X102, 77X104
60 lb.
27 kg
Sound Data
All pumps
See manual 332514, Dyna-Star HP and HF Pump
See manual 332514, Dyna-Star HP and HF Pump

Dyna-Star® HP or HF Pump Low Level Indicator Kit; Dip Stick Kit
Low Level Indicator
Low level sensor switch
Normally open sensor switch; closes upon low level
Normally open sensor switch; closes upon low level
Operating temperature range
–50°F to 150°F
-45°C to 65°C
Switching power
10 Watt Max.
10 Watt Max.
Switching current
0.4A-Max.
0.4A-Max.
Switching voltage
5 to 32 VDC
5 to 32 VDC
Contact resistance
0.150 Ohms-Max.
0.150 Ohms-Max.
Body thread
3/4 inch NPT(m)
3/4 inch NPT(m)
Wetted parts
Cable
nylon coated stainless steel
nylon coated stainless steel
Crimp tab
stainless steel
stainless steel
Dip Stick
Body thread
3/4 inch NPT(m)
3/4 inch NPT(m)
Wetted parts
zinc plated steel
zinc plated steel

Fill Valve
Maximum fluid working pressure
5000 psi
34.4 MPa, 344.7 bar
Relief value
5000 psi ± 10%
34.4 MPa, 344.7 bar ± 10%
Maximum fluid flow
2 gallons per minute
7.57 liters per minute
Outlet port size
3/4 inch NPT
3/4 inch NPT
Vent port size
3/8 inch NPT
3/8 inch NPT
Inlet
ISO 7241–1, Series B standard hydraulic quick disconnect, 1/4 inch coupling
ISO 7241–1, Series B standard hydraulic quick disconnect, 1/4 inch coupling
Wetted parts
Parts: zinc plated steel parts; Seals: Buna-N
Parts: zinc plated steel parts; Seals: Buna-N
Weight
5.06 lbs
2.3 kg