Graco Inc.

Reactor E-10Electric Foam and Polyurea Proportioner

For smaller polyurethane foam or polyurea projects or touch-ups - applies up to 12 lb (5.4 kg) per minute

Where to BuyRequest Info

Graco's Reactor E-10 is a small, ready-to-use system that helps you get in and get smaller jobs done fast without sacrificing performance. The Reactor E-10 sprayers are ideal for plural-component spray, joint-fill jobs and touch-ups. With smart controls that are easy to setup and simple to operate, the E-10 is a natural complement to any proportioning equipment line-up.

Reactor E-10 Main
  • Small size is ideal for on-site portability and hard-to-reach areas
  • One-person operation saves time and money
  • Use as an add-on to your existing spray business
  • Versatile - switch from cold spray to hot spray to foam
  • Saves 30% on material costs compared to disposable foam systems

Small ready-to-use systems with big results!

  1. Electric power is low draw and plugs into standard outlets
  2. Intuitive start, stop and digital temperature display with single knob operation
  3. Pressure balance valves give you quick and easy balancing of system pressures
  4. Balanced proportioning eliminates pressure fluctuations to give you a consistent spray pattern
  5. Easy-to-service fluid section reduces maintenance and increases productivity
  6. Electric motor improves performance and reduces operating costs
  7. Self-contained translucent material tanks show you that you are spraying on-ratio
  8. Heaters and hose give you up to 2000 watts to pre-heat circulating material

 

Reactor E-10
Maximum Fluid Working Pressure
2000 psi
140 bar, 14 MPa
Maximum Fluid Temperature
160°F
71°C
Maximum Ambient Temperature
110°F
43°C
Maximum Output at 340 cycles/min
12 lb/min
5.4 kg/min
Output per Cycle (A and B)
0.00352 gal
0.0133 liter
Overpressure Relief
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
Weight (approximately, depending on model)
160 lb
72 kg
Wetted Parts
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
Electrical Requirements
Model AP9570, CS9570:
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
Model AP9571, CS9571:
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
Model AP9572, CS9572:
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
Model 249806:
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
Model 249808:
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
Generator Size (for Reactor E-10 only)
Heated:
5000 W minimum
5000 W minimum
Nonheated:
2500 W minimum
2500 W minimum
Heater Power
120V models:
850 W each; 1700 W total
850 W each; 1700 W total
240V models:
1000 W each; 2000 W total
1000 W each; 2000 W total
Sounds Pressure
Fast Circulation Mode:
78.7 dB(A)
78.7 dB(A)
At 2000 psi (14 MPa, 140 bar), 0.72 gpm (2.7 lpm):
84.5 dB(A)
84.5 dB(A)
Sound Power, measured per ISO 9416–2
Fast Circulation Mode:
88.6 dB(A)
88.6 dB(A)
At 2000 psi (14 MPa, 140 bar, 0.72 gpm (2.7 lpm):
94.4 dB(A)
94.4 dB(A)
Tank Capacity (nominal)
7 gal
26.5 liters
Fluid Outlets
Component A (ISO):
-5 JIC male
-5 JIC male
Component B (RES):
-6 JIC male
-6 JIC male
Fluid Circulation Ports
Component A (ISO):
-5 JIC male
-5 JIC male
Component B (RES):
-6 JIC male
-6 JIC male
Air Inlet
1/4 in quick-disconnect industrial type pin fitting
1/4 in quick-disconnect industrial type pin fitting
Air Outlet
1/4 npsm(m)
1/4 npsm(m)
Gun Compressed Air Requirements
Fusion Gun (purge air and operating air):
4 scfm
0.112 m³/min
2K Ultra-Lite Gun with disposable mixer kit, with air spray valve fully open:
14 scfm
0.392 m³/min
2K Ultra-Lite Gun with joint fill kit:
2 scfm
0.056 m³/min
Hose Markings
A Side
Red
Red
B Side
Blue
Blue