Dispensit 1052 and 1053 Valves Precision Dispense Valve
Positive displacement metering rod valves for low to high viscosity materials
The Model 1052 & 1053 rod positive displacement valves are designed for volumetric shot-to-shot (1052) or bead (1053) dispensing of a wide variety of materials.
- For low to high viscosity materials with various wetted component configurations
for abrasive filled, or corrosive materials - 1052 is a pneumatically-controlled valve with micrometer adjustable dispense volumes
for accurate, repeatable shot dispensing - 1053 is a servo-driven valve for programmable, precise shot or bead dispensing
- Pneumatic and electronic controls can be integrated for automated applications
- Positive displacement metering
- Wide array of wetted components
Navodila za uporabo
- 3A5115B, Dispensit 4104A, Operation-Maintenance, English (Samo v angleščini)
- 3A0231H, Dispensit 1052, Operation - Maintenance, English (Samo v angleščini)
- 3A0261K, Manual, 1053/1093 Control Box, Setup-Operation, English (Samo v angleščini)
- 3A0874E, Dispensit 1053-10C, Operation - Maintenance, English (Samo v angleščini)
- 313812J, Dispensit 1053-10B, Operation - Maintenance, English (Samo v angleščini)
Literatura
339630EN, Dispensit Single-Component Metering and Dispensing Valves
Dispensit 1053-10C | |
Maximum Ambient Temperature |
110°F
43°C
|
Maximum Operating Temp |
300°F
149°C
|
Maximum Outlet Fluid Working Pressure |
2000 psi
14 MPa, 138 bar
|
Maximum Air Working Pressure |
100 psi
0.7 MPa, 7 bar
|
Minimum Air Working Pressure |
70 psi
480 kPa, 4.8 bar
|
Maximum Material Inlet Pressure |
Metal Sleeves: 1200 psi
8 MPa, 83 bar
|
Plastic Sleeves: 400 psi |
2.8 MPa, 28 bar
2.8 MPa, 28 bar
|
Supplied Air Requirements. |
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
|
Shot Size Range (depending on metering rods selected) |
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
|
Maximum Cycle Rate (application dependent, heat required) . |
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
|
Dimensions (H x L x W), height to end of material inlet |
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
|
2 in.: 17.85 x 6.23 x 2.91 in |
453 x 158 x 74 mm
453 x 158 x 74 mm
|
Graco-supplied Feed System Assemblies (depends on selected options): | |
Smallest: 22.5 x 10 x 4 in. |
572 x 254 x 102 mm
572 x 254 x 102 mm
|
Largest: 60 x 28 x 19 in. |
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
|
Weight |
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
|
Wetted Parts |
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
|
Dispensit 1052 | |
Maximum Ambient Temperature |
110°F
43°C
|
Maximum Operating Temp |
150°F
65°C
|
Maximum Outlet Fluid Working Pressure |
2000 psi
14 MPa, 138 bar
|
Maximum Air Working Pressure |
100 psi
0.7 MPa, 7 bar
|
Minimum Air Working Pressure |
70 psi
480 kPa, 4.8 bar
|
Maximum Material Inlet Pressure |
Metal Sleeves: 1200 psi
8 MPa, 83 bar
|
Plastic Sleeves: 400 psi |
2.8 MPa, 28 bar
2.8 MPa, 28 bar
|
Supplied Air Requirements. |
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
|
Shot Size Range (depending on metering rods selected) |
0.002 cc to 3.600 cc
0.002 cc to 3.600 cc
|
Maximum Cycle Rate (application dependent, heat required) . |
Up to 60 cycles per minute
Up to 60 cycles per minute
|
Dimensions (H x L x W), height to end of material inlet |
16.13 x 5.52 x 2.75 in.
410 x 140 x 70 mm
|
Graco-supplied Feed System Assemblies (depends on selected options): | |
Smallest: 22.5 x 10 x 4 in. |
572 x 254 x 102 mm
572 x 254 x 102 mm
|
Largest: 60 x 28 x 19 in. |
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
|
Weight |
Metering Valve: 4 - 5 lb
1.81 - 2.27 kg
|
Wetted Parts |
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
|
Dispensit 1053-10B | |
Maximum Ambient Temperature |
110°F
43°C
|
Maximum Operating Temp |
150°F
65°C
|
Maximum Outlet Fluid Working Pressure |
2000 psi
14 MPa, 138 bar
|
Maximum Air Working Pressure |
100 psi
0.7 MPa, 7 bar
|
Minimum Air Working Pressure |
70 psi
480 kPa, 4.8 bar
|
Maximum Material Inlet Pressure |
Metal Sleeves: 1200 psi
8 MPa, 83 bar
|
Plastic Sleeves: 400 psi |
2.8 MPa, 28 bar
2.8 MPa, 28 bar
|
Supplied Air Requirements. |
1 to 3 cfm at 80 psi to 100 psi
1 to 3 cfm at 80 psi to 100 psi
|
Shot Size Range (depending on metering rods selected) |
0.002 cc to 3.150 cc
0.002 cc to 3.150 cc
|
Maximum Cycle Rate (application dependent, heat required) . |
Up to 15 cycles per minute (with standard Graco motor)
Up to 15 cycles per minute (with standard Graco motor)
|
Dimensions (H x L x W), height to end of material inlet |
1 in.: 14.83 x 6.23 x 2.91 in.
377 x 158 x 74 mm
|
2 in.: 17.85 x 6.23 x 2.91 in |
453 x 158 x 74 mm
453 x 158 x 74 mm
|
Graco-supplied Feed System Assemblies (depends on selected options): | |
Smallest: 22.5 x 10 x 4 in. |
572 x 254 x 102 mm
572 x 254 x 102 mm
|
Largest: 60 x 28 x 19 in. |
(1524 x 711 x 483 mm
(1524 x 711 x 483 mm
|
Weight |
Metering Valve: 3 - 5 lb
1.36 - 2.27 kg
|
Wetted Parts |
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
Metering Valve: Hardened steel, 303/304, 404, UHMWPE, Tungsten, carbide, fluoroelastomer, EPDM, PTFE, Acetal. Graco-supplied Feed System Hoses and Fittings: Mild steel, 303/304, PTFE, buna, polyethylene, polypropylene. Graco-supplied Tanks: Polyethylene, 303/304, mild steel
|