Graco Inc.

Reactor 2 E-XP2i  Integrated Proportioning System

Turnkey system for polyurea waterproof coating and lining - applies up to 2 gal (7.6 liters) per minute

Kust ostaTeabepäring

The integrated series of Reactor 2 systems combines an electric proportioner and diesel generator into one package - an innovative, cost-saving design. In addition, the system offers the many advantages of the revolutionary Reactor 2 design.

Integrated design repurposes wasted heat and saves energy

  • System pulls the heat from the diesel engine to heat the A and B materials, reducing electrical demand on the generator (See illustration for details)
  • The system's smaller 20 kw generator uses less fuel than a standard 30 or 40 kw generator
  • You benefit from an annual fuel savings on average of $7,000 (actual savings may vary)

Reactor 2 advanced features can revolutionize the way you run your business

Each feature in the Reactor 2 was strategically designed to help your business, with innovations that help your operation run smoothly. Software and hardware enhancements for better spray performance. And new technologies that add to your bottom line.

  • Better control - with Graco InSite remote reporting, you can manage your spray foam or polyurea business wherever you are
  • Better documentation - collect job log data automatically and confirm you sprayed to specifications
  • Compact footprint - more room in your spray rig
  • Advanced controls with more visible information and tracking capabilitiy
  • Ergonomic design - easier maintenance and service
  • Better spraying performance compared to traditional electric Reactor systems
  • Advanced circuit boards - minimize pressure fluctuations
  • Better management of fleet, crew, cost containment and forecasting
  • Troubleshooting made quick and easy with QR codes
  • 3-year warranty on major electronic components
  • Energy-saving integrated design
  • Graco InSite Remote Reporting Technology
  • Inlet pressure and temperature sensors
  • Advanced control module
  • Stores up to 24 chemical recipes
  • Easy-to-see drum level indicators
  • More compact design
  • New multi-zone heater control module
  • Brushless DC motor
  • On-screen QR codes for faster troubleshooting information
  • Extreme-Wrap scuff guard
  • Hydrovane tankless air compressor (optional)
  • Refrigerated air dryer (optional)

Reactor 2 Elite Integrated Proportioning Systems
U.S.
Metric
Metric
Maximum Fluid Working Pressure
E-30i
2000 psi
14 MPa, 140 bar
E-XP2i
3500 psi
24.1 MPa, 241 bar
Maximum Fluid Temperature
E-30i
150°F
65°C
E-30i with booster heater
180°F
82°C
E-XP2i
180°F
82°C
Maximum Output
E-30i
30 lb/min
13.5 kg/min
E-XP2i
2 gpm
7.6 lpm
Maximum Heated Hose Length
Length
310 ft
94 m
Output per Cycle, A and B
E-30i
0.0272 gal.
0.1034 liter
E-XP2i
0.0203 gal.
0.0771 liter
Operating Ambient Temperature Range
Temperature
20° to 120°F
-7° to 49°C
Auxiliary Power Available
Voltage
120 Vac or 240 Vac, 60 Hz
120 Vac or 240 Vac, 60 Hz
Engine
Model
Perkins 404–22G, 2.2 L, 29 HP
Perkins 404–22G, 2.2 L, 29 HP
Alternator
Model
Mecc Alte 22 kW, 240 V, 1 PH, 60 Hz, pancake style
Mecc Alte 22 kW, 240 V, 1 PH, 60 Hz, pancake style
Battery Requirements
Voltage
12 Vdc
12 Vdc
Minimum Cold Cranking Amps
800 CCA
800 CCA
Connection Type
Post Style
Post Style
Recommended Battery Size
BC Group Number
34
34
Length
10.25 in.
260 mm
Width
6.81 in.
173 mm
Height
7.88 in.
200 mm
Booster Heater Power
E-30i
None
None
E-30i with booster heat
4000 Watts
4000 Watts
E-XP2i
4000 Watts
4000 Watts
Rotary Vane Air Compressor
Hydrovane Model V04 (PURS type), continuous run
Part No.
025CK10
025CK10
Pressure
140 psi
0.9 MPa, 9.6 bar
Specifications
16 cfm
16 cfm
Required Features
Thermal overload switch, Safety Relief Valve
Thermal overload switch, Safety Relief Valve
Motor: Baldor
Part No.
EL1410–CUS
EL1410–CUS
Specifications
5 HP, 1735 RPM, 240 V, 1 Phase, OPSB
5 HP, 1735 RPM, 240 V, 1 Phase, OPSB
Required Features
C face, lift rings
C face, lift rings
Refrigerated Air Dryer
Hankison Model H1T20
Specifications
115VAC, 1 Phase, 60 Hz, 22 scfm at 150 psi (1 MPa, 10.3 bar)
115VAC, 1 Phase, 60 Hz, 22 scfm at 150 psi (1 MPa, 10.3 bar)
Required Features
Pilot valve unloader
Pilot valve unloader
Noise, Sound Pressure measured per ISO-9614–2.
Sound Pressure measured from 3.1 ft (1 m), at 1500 psi (10 MPa, 103 bar), 2 gpm (7.6 lpm)
91.0 dBA
91.0 dBA
Fluid Inlets
Component A (ISO) and Component B (RES)
3/4 NPT(f) with 3/4 NPSM(f) union
3/4 NPT(f) with 3/4 NPSM(f) union
Fluid Outlets
Component A (ISO)
#8 (1/2 in.) JIC, with #5 (5/16 in.) JIC adapter
#8 (1/2 in.) JIC, with #5 (5/16 in.) JIC adapter
Component B (RES)
#10 (5/8 in.) JIC, with #6 (3/8 in.) JIC adapter
#10 (5/8 in.) JIC, with #6 (3/8 in.) JIC adapter
Fluid Circulation Ports
Size
1/4 NPSM(m), with sst braided tubing
1/4 NPSM(m), with sst braided tubing
Maximum Pressure
250 psi
1.75 MPa, 17.5 bar
Weight
E-30i
1750 lb
794 kg
E–30i with compressor and dryer
2200 lb
998 kg
E-30i with booster heat
1800 lb
816 kg
E–30i with booster heat, compressor, and dryer
2250 lb
1021 kg
E-XP2i
1800 lb
816 kg
E–XP2i with compressor and dryer
2200 lb
998 kg
Wetted Parts
Material
Aluminum, stainless steel, zinc plated carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
Aluminum, stainless steel, zinc plated carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene