- Small size is ideal for on-site portability and hard-to-reach areas
- One-person operation saves time and money
- Use as an add-on to your existing spray business
- Versatile - switch from cold spray to hot spray to foam
- Saves 30% on material costs compared to disposable foam systems
Reactor E-10 Electric Foam and Polyurea Proportioner
For smaller polyurethane foam or polyurea projects or touch-ups - applies up to 12 lb (5.4 kg) per minute
Graco's Reactor E-10 is a small, ready-to-use system that helps you get in and get smaller jobs done fast without sacrificing performance. The Reactor E-10 sprayers are ideal for plural-component spray, joint-fill jobs and touch-ups. With smart controls that are easy to setup and simple to operate, the E-10 is a natural complement to any proportioning equipment line-up.

Small ready-to-use systems with big results!
- Electric power is low draw and plugs into standard outlets
- Intuitive start, stop and digital temperature display with single knob operation
- Pressure balance valves give you quick and easy balancing of system pressures
- Balanced proportioning eliminates pressure fluctuations to give you a consistent spray pattern
- Easy-to-service fluid section reduces maintenance and increases productivity
- Electric motor improves performance and reduces operating costs
- Self-contained translucent material tanks show you that you are spraying on-ratio
- Heaters and hose give you up to 2000 watts to pre-heat circulating material
Vadovai
Literatūra
- 300615ENEU Reactor Spray Foam and Polyurea Equipment [kitos kalbos]
- 349104ENEU, Hoses, Guns and Accessories [kitos kalbos]
- 349730EN, DataTrak Control (Tik anglų k.)
- 300738ENEU SHIP & RIG BUILDING [kitos kalbos]
- 349435EN-A, Reactor Maintenance Schedule (Tik anglų k.)
- 349890EN, Spray Foam Equipment Brochure (Tik anglų k.)
- 350238ENEU White Paper Ratio Assurance [kitos kalbos]
300615ENEU Reactor Spray Foam and Polyurea Equipment
349104ENEU, Hoses, Guns and Accessories
Reactor E-10 | |
Maximum Fluid Working Pressure |
2000 psi
140 bar, 14 MPa
|
Maximum Fluid Temperature |
160°F
71°C
|
Maximum Ambient Temperature |
110°F
43°C
|
Maximum Output at 340 cycles/min |
12 lb/min
5.4 kg/min
|
Output per Cycle (A and B) |
0.00352 gal
0.0133 liter
|
Overpressure Relief |
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
Recirc/Spray valves automatically relieve excessive fluid pressure back to supply tanks
|
Weight (approximately, depending on model) |
160 lb
72 kg
|
Wetted Parts |
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
Aluminum, stainless steel, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
|
Electrical Requirements | |
Model AP9570, CS9570: |
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits
|
Model AP9571, CS9571: |
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits
|
Model AP9572, CS9572: |
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit
|
Model 249806: |
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15 A circuit
|
Model 249808: |
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
240 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 8 A circuit
|
Generator Size (for Reactor E-10 only) | |
Heated: |
5000 W minimum
5000 W minimum
|
Nonheated: |
2500 W minimum
2500 W minimum
|
Heater Power | |
120V models: |
850 W each; 1700 W total
850 W each; 1700 W total
|
240V models: |
1000 W each; 2000 W total
1000 W each; 2000 W total
|
Sounds Pressure | |
Fast Circulation Mode: |
78.7 dB(A)
78.7 dB(A)
|
At 2000 psi (14 MPa, 140 bar), 0.72 gpm (2.7 lpm): |
84.5 dB(A)
84.5 dB(A)
|
Sound Power, measured per ISO 9416–2 | |
Fast Circulation Mode: |
88.6 dB(A)
88.6 dB(A)
|
At 2000 psi (14 MPa, 140 bar, 0.72 gpm (2.7 lpm): |
94.4 dB(A)
94.4 dB(A)
|
Tank Capacity (nominal) |
7 gal
26.5 liters
|
Fluid Outlets | |
Component A (ISO): |
-5 JIC male
-5 JIC male
|
Component B (RES): |
-6 JIC male
-6 JIC male
|
Fluid Circulation Ports | |
Component A (ISO): |
-5 JIC male
-5 JIC male
|
Component B (RES): |
-6 JIC male
-6 JIC male
|
Air Inlet |
1/4 in quick-disconnect industrial type pin fitting
1/4 in quick-disconnect industrial type pin fitting
|
Air Outlet |
1/4 npsm(m)
1/4 npsm(m)
|
Gun Compressed Air Requirements | |
Fusion Gun (purge air and operating air): |
4 scfm
0.112 m³/min
|
2K Ultra-Lite Gun with disposable mixer kit, with air spray valve fully open: |
14 scfm
0.392 m³/min
|
2K Ultra-Lite Gun with joint fill kit: |
2 scfm
0.056 m³/min
|
Hose Markings | |
A Side |
Red
Red
|
B Side |
Blue
Blue
|
Priedai
-
Fusion Air Purge
For high output spray polyurethane foam and polyurea applications
-
Fusion CS
For high output spray polyurethane foam and polyurea applications
-
Graco InSite
Sends Reactor data to your smart phone, tablet or computer.
-
Probler P2
For high output spray polyurethane foam and polyurea applications
-
T1, T2 and T3 Transfer Pumps
Ideal for moving A and B materials to Reactor spray machines
-
Twistork Agitators
For mixing fluids in closed drums
Susiję produktai
-
Reactor 2 E-30
Next generation technology for spray foam insulation and polyurea
-
Reactor 2 E-30i
Turnkey system for spray foam insulation and coating - applies up to 30 lb (13.6 kg) per minute
-
Reactor A-25
For spraying foam insulation - applies up to 25 lb (11.4 kg) per minute
-
Reactor E-10hp
Entry-level system for pure and hybrid polyurea coatings
-
Reactor E-20
For low- to medium-output foam insulation applications - applies up to 20 lb (9 kg) per minute
-
Reactor E-8p for Flooring
For small to mid-sized no-heat joint fill applications