Endura-Flo 3D High Pressure Diaphragm Pumps
Extra Life when you want it
The 3:1 model has no air backing the diaphragm. This Isolated Air Section results in a lower pressure range than the 4:1 model, but will extend the diaphragm life.
The Isolated Air Section will prevent fluids from enterring the air section and muffler. As there is no air backing the diaphragm, the maintenance cycles are reduced and it has less components to replace.
- Low Pulsation and Low Shear
- Ideal for fluid transfer and supply, small paint circulation and piggable paint systems
- Easy access to critical components for easy maintenance and fast repair
- Diaphragm requires very little solvent to flush
- 360 ° mounting possibility
- Consistent start-up pressure (ideal for piggable systems)
- Pumps are easily configurable for custom installations
- DataTrek option prevents runaway and tracks material usage
Navodila za uporabo
Literatura
Drugi viri
- CAD Drawing (2D) - Endura-Flo 4D350 (Samo v angleščini)
- CAD Drawing (3D) - Endura-Flo 4D350 (Samo v angleščini)
- CAD Drawing (2D) - DataTrak (Samo v angleščini)
- CAD Drawing (3D) - DataTrak (Samo v angleščini)
Endura-Flo 4D350 Diaphragm Pump | |
Maximum air input pressure | 100 psi 7 bar, 0.7 MPa |
Maximum inlet feed pressure* | 70 psi 4.8 bar, 0.48 MPa |
Maximum fluid working pressure | 400 psi 28 bar, 2.8 MPa |
Maximum static fluid pressure | 430 psi 30 bar, 3.0 MPa |
Ratio | 4:1 4:1 |
Maximum recommended continuous cycle rate | 20 cycles per minute 20 cycles per minute |
Volume per cycle (double stroke) | 12 oz per cycle 350 cc per cycle |
Ambient and operating temperature range. Use dry compressed air when operating at low temperatures. | 32 to 122°F 0 to 50°C |
Dry suction lift | 23 ft 7.0 m |
Wet suction lift | 29 ft 8.8 m |
Air inlet size | 1/2 npt 1/2 npt |
Fluid inlet size | 1 in. Tri-Clamp Flange, 3/4 in npt, or 3/4 in bspp 1 in. Tri-Clamp Flange, 3/4 in npt, or 3/4 in bspp |
Fluid outlet size | 1 in. Tri-Clamp Flange, 3/4 in npt, or 3/4 in. bspp 1 in. Tri-Clamp Flange, 3/4 in npt, or 3/4 in. bspp |
Weight (approximate) | 72 lb 33 kg |
Wetted parts | stainless steel, perfluoroelastomer (FFKM), PTFE, Polyphenylene Sulfide (PPS) stainless steel, perfluoroelastomer (FFKM), PTFE, Polyphenylene Sulfide (PPS) |
* NOTE: When pressure feeding the pump inlet, do not allow the outlet pressure to exceed the Maximum Fluid Working Pressure. The inlet feed pressure will pressurize the outlet by the corresponding amount.Example: Pressure feeding the inlet with 60 psi and supplying 80 psi air pressure will result in the following: 80 psi * 4:1 + 60 psi = 380 psi fluid pressure. |
-
Kmetijska oprema – izdelava
-
Gradbena oprema – izdelava
-
Premazi, odporni proti kemičnim bojnim strupom
-
Površinska obdelava/izdelava pohištva
-
Splošna površinska obdelava/izdelava kovin
-
Izdelava lesnih izdelkov
-
Železnice
-
Ravnanje z odpadki – izdelava opreme
-
Osebna vozila za rekreacijo
-
Avtodomi
-
Les in lesni izdelki – črpalke
-
Izdelava težke opreme