E-Flo 4-Ball
E-Flo 4-Ball Electric Circulation Pump, 1500cc, Sealed, Ultralife Rod/Cylinder, Tri-Clamp, Stand
EP00G1


E-Flo 4-Ball
E-Flo 4-Ball Electric Circulation Pump, 1500cc, Sealed, Ultralife Rod/Cylinder, Tri-Clamp, Stand
EP00G1
The dual lower of the E-Flo electric circulating pump minimizes pressure changes at the outlet of the pump. Online maintenance simplifies repair and reduces downtime. Accomplish remote monitoring of performance via computer or PLC for a higher degree of control.
Questions About this Product?
If you’re not finding the information you need, ask one of our experts.
Ask an ExpertFeatures
Product Brochure
The dual lower of the E-Flo electric circulating pump minimizes pressure changes at the outlet of the pump. Online maintenance simplifies repair and reduces downtime. Accomplish remote monitoring of performance via computer or PLC for a higher degree of control.
- Sealed lower has longer maintenance cycles, plus it can be used for every pumping application in your mix room, including catalyzed coatings
- 3 times more efficient than pneumatics
- Process control and feedback
- Slow smooth change overs
- Low noise
- Open wet cup version is also available
Specifications & Documents
Technical Specifications
Convert to MetricApplication | Circulation |
---|---|
Compatible Material | Solventborne, High Solids, Xirallic, Metallics, Varnish, CARC |
Fluid Inlet Size (in) | 2 |
Fluid Outlet Size (in) | 2 |
Fluid Section Type | Sealed |
Material | Stainless Steel |
Maximum Continuous Cycle Rate (CPM) | 20 |
Maximum Flow Rate (GPM) | 8.1 |
Maximum Operating Temperature (°F) | 104 |
Maximum Working Pressure (MPa) | 2.9 |
Maximum Working Pressure (psi) | 425 |
Minimum Operating Temperature (°F) | 32 |
Motor Type | None |
Portable | Non-Portable |
Standards Met | N/A |
Type | Electric Piston Pump |
Wetted Material | Stainless Steel |
Application | Circulation |
Compatible Material | Solventborne, High Solids, Xirallic, Metallics, Varnish, CARC |
Fluid Inlet Size (cm) | 5.08 |
Fluid Inlet Size (mm) | 50.8 |
Fluid Outlet Size (cm) | 5.08 |
Fluid Outlet Size (mm) | 50.8 |
Fluid Section Type | Sealed |
Material | Stainless Steel |
Maximum Continuous Cycle Rate (CPM) | 20 |
Maximum Flow Rate (L/min) | 30.66 |
Maximum Operating Temperature (°C) | 40 |
Maximum Working Pressure (MPa) | 2.9 |
Maximum Working Pressure (bar) | 29 |
Maximum Working Pressure (kPa) | 2900 |
Minimum Operating Temperature (°C) | 0 |
Motor Type | None |
Portable | Non-Portable |
Standards Met | N/A |
Type | Electric Piston Pump |
Wetted Material | Stainless Steel |
Product Manuals
311876N, 4-Ball Lower Retrofit Connection Kits, Instructions, Parts List, English
(1 MB)
(English Only)
Certifications
Repair Parts
Part No. | Description |
---|---|
17K656 | Sealed 4-Ball Lower, 750 cc, Stainless Steel, Ultralife Rod & Cylinder, Tri-Clamp Fittings |
15H877 | TDC Sensor Kit |
15J422 | Inlet/Outlet Fitting, converts 1-1/2 tri-clamp to 1-1/2 npt |
15J423 | Inlet/Outlet Fitting, converts 2 tri-clamp to 2 npt |
15K012 | Air pressure to the BPR Control Kit |
16C487 | Coupler Kit for NEMA 182-184 TC Frame 3 or 5 HP motors. Includes 2.25 in. (57.2 mm) key |
289550 | Gear Reducer Replacement Kit for E-Flo 1500 Pumps |
15H874 | Slider Cylinder Rebuild Kit |
15H885 | Ethernet Interface Kit |
24H372 | ACS Module for E-Flo Circulation Pumps |
247341 | Slider Cylinder Collector Kit |
15J378 | Crank Arm Cover Kit |
15J639 | Inlet/Outlet Fitting, converts 1-1/2 tri-clamp to 2 tri-clamp |
15H871 | Gear Reducer Seal Kit |
15H873 | Drive Linkage Rebuild Kit |
15H882 | Slider Bearing Kit |
15H886 | Gear Reducer Replacement Kit for E-Flo 2000/3000/4000 Pumps |
15H880 | Motor coupler kit- to install electric motors on E-Flo® 4-Ball Piston Pumps |
255216 | Wrist Pin Replacement Kit |
15H878 | Manifold Gasket Kit |
15H883 | Crank Arm Kit |
15J926 | Output Shaft Seal Tool Kit |
24E453 | Motor Mounting Kit for IEC 112M/B5 and 100L/B5 Frame Electric Motors, includes motor adapter plate |
24J305 | Sensor Circuit Option Kit for E-Flo Pumps (Series D and later) |